QMS 1725 SLS Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 328

background image

Tray Chaining

3-11

Daily Operations

slot as shown in the following illustration, with the face up and the flap
side toward the left manual feed guide.

Because envelopes pass through heated rollers, the gummed area
on the flap may seal. Open the flap immediately after it passes
through the printer, before the seal cools. You may then reseal in the
normal manner. The use of envelopes with emulsion-based glue
avoids this problem.

»

Note: Before printing envelopes, disable the duplexer if it is installed and

check the manual feed guides to make sure theyre not too tight and

buckling the envelopes. Also, make sure envelopes meet specifications listed

in appendix B, Technical Specifications. If envelopes curl excessively, use

the face-up output bin at the rear of the printer.

The Optional Envelope Feeder

To load up to 100 envelopes at a time, use the optional envelope
feeder. Instructions for installation and use are in chapter 8, “Printer
Options.” See your QMS vendor for more information on the optional
envelope cassette.

Tray Chaining

This printer has two cassettes (also known as trays or input bins) for a
total media capacity of approximately 1000 sheets before a reload is

Manual feed guides

«
...
111
112
113
114
115
...
»

Содержание 1725 SLS









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1725 SLS

SCX-4300 - SCX 4300 B/W Laser

Бренд: Samsung Страницы: 97

SCX 4828FN - Laser Multi-Function Printer

Бренд: Samsung Страницы: 151

SCX 4725FN - B/W Laser - All-in-One

Бренд: Samsung Страницы: 120

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 97

SCX 4200 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 95

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 172

ProXpress M337x

Бренд: Samsung Страницы: 56

PROXPRESS M332 SERIES

Бренд: Samsung Страницы: 50

ML-2240 - 23 Ppm Mono Laser Printer

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 8

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 134

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 112

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 152

ML 3471ND - B/W Laser Printer

Бренд: Samsung Страницы: 207

ML 2150 - B/W Laser Printer

Бренд: Samsung Страницы: 237

ML 3471ND - B/W Laser Printer

Бренд: Samsung Страницы: 103

ML 2150 - B/W Laser Printer

Бренд: Samsung Страницы: 217

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды