- 3 -
SAFETY INSTRUCTIONS FOR TILE SAW
READ THIS OWNER’S MANUAL COMPLETELY AND MAKE SURE YOU UNDERSTAND ALL OF IT’S SAFETY
GUIDELINES.
1.
KEEP GUARDS IN PLACE
and in working order.
2.
REMOVE ADJUSTING KEYS AND WRENCHES.
Before turning on the tile saw, make sure the keys and adjusting
wrenches have been removed.
3.
KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4.
ALWAYS REMAIN ALERT WHEN THE SAW IS IN USE.
Inattention on the part of the operator may lead to
serious injury.
5.
DON’T USE IN A DANGEROUS ENVIRONMENT
. Don’t use power tools in damp or wet locations or expose
them to rain. Keep work area well lighted.
6.
KEEP CHILDREN AWAY
. All visitors should remain at a safe distance from work area.
7.
MAKE WORKSHOP CHILD-PROOF
with padlocks, master switches or by removing starter keys.
8.
USE RIGHT TOOL.
Don’t force tool or attachment to do a job for which it was not designed.
9.
USE PROPER EXTENSION CORD.
Make sure your extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size
to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
10.
DON’T FORCE TOOL.
It has been designed to operate at maximum safety and performance levels.
11.
DO NOT FORCE THE MATERIAL BEING CUT
. Always let the blade cut at its own speed.
12.
WEAR PROPER APPAREL.
Do not wear loose clothing, neckties, rings, bracelets or other jewelry which may get
caught in moving parts. Non-slip foot wear is recommended. Wear protective hair covering if you have long
hair.
13.
ALWAYS USE SAFETY GLASSES.
Also use face or dust mask
for
commercial
cutting
operations.
Everyday
eyeglasses only have impact-resistant lenses, they are
NOT
safety glasses.
14.
SECURE WORK.
Use clamps or a vise instead of your hand to
hold work when practical. This safety precaution allows for
proper tool operation using both hands.
15.
DON’T OVERREACH
. Keep proper footing and balance at all
times.
16.
MAINTAIN TOOLS WITH CARE.
Keep tools clean and in good
working condition for maximum safety performance. Follow
instructions for lubricating and changing accessories.
17.
DISCONNECT TOOLS BEFORE SERVICING
– when changing
accessories, such as blades, bits, cutters, etc.
18.
REDUCE THE RISK OF UNINTENTIONAL STARTING
. Make
sure switch is in OFF position before plugging in.
19.
USE RECOMMENDED ACCESSORIES.
Consult the owner’s
manual for recommended accessories. The use of improper
accessories may increase risk of injury.
20.
DO NOT DRY CUT WITH BLADES DESIGNED FOR WET CUTS.
21.
MAKE SURE YOU USE THE CORRECT BLADE
for the job you are doing.
22.
NEVER STAND ON TOOL.
Serious injury could occur if the tile saw is tipped or if the cutting tool is
unintentionally contacted.
23.
CHECK DAMAGED PARTS.
Before further use of the tool, damaged part(s), (i.e. guard) should be carefully
checked to determine that it will operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect
the saw’s operation. A guard or other part that is damaged should be properly repaired or replaced.
24.
ENSURE THAT THERE IS A CONTINUOUS FLOW OF WATER
to both sides of blade during operation.
25.
CHECK DIAMOND BLADES CAREFULLY FOR CRACKS, NICKS, MISSING DIAMOND MATRIX OR OUT-OF-
ALIGNMENT CONDITION.
Replace damaged blades immediately.
DO NOT USE DAMAGED BLADES.
They may
cause bodily injury.
26.
DIRECTION OF FEED.
Feed work into the blade against the direction of rotation of the blade only.
27.
DO NOT ALTER THE PLUG OR USE A 2-PRONG RECEPTACLE.
This saw is equipped with a 3-prong electrical
plug.
28.
NEVER LEAVE TOOL RUNNING UNATTENDED.
Turn power off. Don’t leave tool until it comes to a
complete stop.
ILLUSTRATION 1
DRIP LOOP
60024 MANUAL-tri.qxd:60024 MANUAL-tri.qxd 4/23/09 4:45 PM Page 3
Содержание 60024
Страница 5: ...1 2 0 ...
