background image

17

TROUBLESHOOTING

Troubleshooting

Use the following troubleshooting table to assist in troubleshooting the MP10: 

Display not showing

Symptom

Low or dead batteries
Batteries installed wrong

Check battery voltage on
opening display (>3.6 volts
required)
Replace batteries
Check battery connection

Controller not cycling

Low or dead batteries

See, above

MP10 not STARTED with 
CYCLE key
MP10 in HELD mode

Operate CYCLE and/or 
PAUSE key to return MP10
to cycling state

MP10 in LEVEL hold

Make sure MP30 probe is
submerged when in MP
mode

Temperature below 10F

Warm controller

Air not cycling through
controller

Throttle turned too low

Turn throttle clock-wise to
produce pressure

Air source not delivering air

Verify air source

Pump not pumping

Throttle turned too low

Turn throttle clock-wise to
produce pressure

Time settings not correct

Try different CPM settings
(lower CPM for deeper
wells) and/or different refill
and discharge time settings

Air source pressure too low

Verify air source pressure

Battery life too short

Controller left on while strored Turn MP10 off before

storing and remove
batteries when storing more
than 1 month

Temperature below 10F

Warm controller

Possible Cause

Action / Fix

Lid not open

Open lid

Содержание Micropurge MP10


























Отзывы: