QED AP4 Ultra Скачать руководство пользователя страница 24

Chapter 7: Troubleshooting & Repairs 

Returning Equipment for Service

1.

Call the QED Service Department and obtain a Return Material Authorization (RMA) number.  Please have 

    available the contact person’s name, company name and address, phone number, fax number, reason for the 

    return, and the names of the chemicals to which the equipment has been exposed.

2.

Clean all equipment before shipping. (

See Equipment Cleaning Requirements at the end of this section

). If the 

    equipment must be cleaned after it arrives at QED, the customer will be charged for the cleaning and disposal of 

    material, if necessary.  (Cost can be $500.00 per piece of equipment cleaned.)  It is also important to note that

    shipping equipment with a known hazardous waste is a 

violation of federal law

. Drain and dry all equipment after 

    cleaning.

3.

Package the equipment so that it will not be damaged in shipment.  Use bubble pack rather than styrofoam flakes

    as packing material.

4.

Ship the equipment via a carrier and service level (i.e., one-day, two-day shipping) in consideration of probable 

    service time and return shipment time.

5.

It is recommended that such shipments be insured so, if the shipment is badly damaged or lost, the customer can 

    replace the equipment at little or no cost.

6.

Include the contact’s name, company, phone number and RMA number given by QED.

7.

Write the RMA number on the outside of the packaging so it will be directed immediately to the QED Service 

    Department.

If the equipment needs to be returned to QED for servicing, please follow these steps:

Equipment Cleaning Requirements

2.

Rinse all soap off of the equipment.

3.

Soak and rinse the outside of the unit with water to remove loose debris and dirt.

If the equipment is to be shipped to another site or to the factory for service, it needs to be thoroughly cleaned before 

leaving the site.  Cleaning the equipment protects the user (sender), the shipper, and the receiver from dirt and/or 

contaminants.  If the equipment is not cleaned prior to shipping for servicing, it may be severely delayed, refused or 

the shipper may be charged a cleaning fee.  Before packing and shipping, ensure that the equipment is dry inside and 

out.

Revision 3 - December, 2013

Revision 3 - December, 2013

(First check lever pivot wear per #6 above)

Call the QED Service Department for correct air valve timing for your pump.

9. Air Inlet Valve Timing

1.

Pump clean water or water with a gentle soap solution (e.g. Dish Soap) through the pump to remove free product 

and particles.

To Clean the AP

 Ultra

:

4.

Pressure wash

 inside and out to remove difficult dirt and contaminants.

Caution:

 Use low pressure (less than 40 psi

(2.76 bar)

) when 

pressure wash

ing.

2

1

Содержание AP4 Ultra












































Отзывы: