INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK_DUO-G10.X
INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK_DUO-G10.X
8
9
2 Planning
2.3 Mounting options
TYPE OF
INSTALLATION
POINT MOUNTING SYSTEM
LINEAR MOUNTING SYSTEM
Installation
on mounting
points
EN
4 x Mounting
points
368.5
FB1
EN
4 × Mounting
points
368.5
FB2
Installation
with insertion
profiles
not permitted
IP1
IP2
IP1
IP2
Specifications
MOUNTING
OPTION
POSITION OF
CLAMPS* [MM]
TEST LOAD
PUSH / PULL** [Pa]
DESIGN LOAD
PUSH / PULL** [Pa]
SAFETY
FACTOR
CL1a
130 - 350
5400 / 4000
3600 / 2660
1.5
20 - 450
5400 / 3600
3600 / 2400
20 - 650
2400 / 2400
1600 / 1600
CL1b
300 - 500
2400 / 2400
1600 / 1600
CL2a
(with rails)
20 - 300***
3600 / 2400
2400 / 1600
CL2b
(without rails)
20 - 200
2400 / 2400
1600 / 1600
CL3
240 - 350
4000 / 4000
2660 / 2660
FB1
368.5
5400 / 4000
3600 / 2660
FB2
368.5
4000 / 4000
2660 / 2660
IP1
-
3600 / 3300
2400 / 2200
CL5
short side: 20 - 100
long side: 300 - 450
CL6a
outer clamps: 20 - 400
middle clamps: 560 - 1160***
8100 / 4000
5400 / 2660
CL6c
outer clamps: 20 - 400
middle clamps: 560-1160***
3600 / 3600
2400 / 2400
CL6d
short side: 20 - 250
long side: 560-1160***
4000 / 3600
2660 / 2400
*
**
***
Distance between outer edge of module and middle of the clamp; consider further details below.
Loads according to IEC 61215-2:2016 and UL 61730.
Rails must not be under the junction box.
MOUNTING OPTIONS
REQUIREMENTS
All
The loads in the table are related to the mechanical stability of the solar modules. The
mechanical stability of the mounting system including clamps has to be evaluated by the system
supplier. The listed test load values have been determined with the following clamp parameters:
clamp width = 40 mm and clamp depth = 10 mm.
The system installer is responsible for the determination of location-specific load requirements.
Ensure that the connection cables of the junction box do not run between laminate and
mounting rails.
Modules bend under load. Therefore, sharp objects (e.g. screws, ballast stones, rail ends, rails
with burrs or sharp corners) must not be placed near the module backside so as not to touch
the laminate under load.
Ensure that the junction boxes do not touch the mounting structure (e.g. shorts rails, ballast, etc.)
or the rooftop under load. Clamps or insertion profiles etc. must not touch the glass (even under
load).
Unbalanced loads (e.g. snow overhangs, snowdrifts) which result in locally significantly
increased loads must be removed or avoided by technical measures.
CL1a, CL2a, CL3,
CL6a, FB1, FB2
Ensure that module frame is fixed directly on the rail of the substructure (no spacer allowed
between the module and substructure).
CL1a
At push test loads of 5400 Pa: The clamp position is variable in the given range but the distance
between the clamps along the long side of the module (span) must not be larger than 1250 mm.
CL1b
Using of short mounting rails are permissible, if they overlap under the module less than
210 mm. Minimum clearance between frame bottom edge and roof top must be ≥ 35 mm.
CL1b, CL2b, CL3,
FB2, CL6c, CL6d
A minimum support depth of 15 mm is required on the back side of the module.
CL5
The minimum required support depth on the module backside is 10 mm on long frame side and
15 mm on short frame side.
IP1
Ensure minimum support depth of 15 mm on the backside and 10 mm on the front side of the
module.
FB1, FB2
Use M8 corrosion-proof screws and washers (diameter ≥ 15.8 mm) for mounting slots (Detail A,
Fig.1). Mounting screws and washers should have the same material properties.
CL6c, CL6d
Use of short mounting rails under the modules are permissible, if they do not touch the laminate
under load.
2 Planning
2.3 Mounting options
