WARNING - the use of alcohol, drugs, or medication can
greatly increase the risk of fatal hyperthermia in hot tubs
and spas.
S p a L o c a t i o n
The selection of a site for the installation of your spa
is a very important decision and should be undertaken
keeping several factors in mind.
1. Always check your local codes before installing your
spa. A clear understanding of buildings, fences, gates,
electrical and plumbing guidelines will be invaluable.
2. Select a location that will compliment your lifestyle
and your home. The spa will become an integral part
of your life and therefore should be placed
advantageously.
3.
The position of the spa in relation to surrounding
terrain should be considered. Locating the spa near or
directly under trees not only cuts off the sun thereby
depriving you of natural heat, but also necessitates the
physical removal of leaves and debris. Airborne dirt
and debris may also be carried into the spa by
prevailing winds. In addition, an uncovered spa with
wind blowing across the top will tend to lower water
temperatures; therefore you may wish to shield your
spa from direct winds.
4. You may wish to consider an indoor installation. An
indoor spa located off of a bedroom or family room
can offer relaxing solitude or enjoyable gatherings of
friends or family. Care should be taken in providing
protection from possible water damage due to
splashing. High humidity levels relating to the spa can
also be a source for damage and should be planned for
in the construction stage.
5. Your portable spa with a cabinet has been designed to
be self-supporting. Any further reinforcement or
support is not required when placed upon a sound
foundation. In order to prevent damage to the cabinet
and spa be certain to locate the spa on a solid, level
foundation capable of maintaining the weight of the
spa when filled with water.
6. A base of poured concrete is best for this type of
installation. You may wish to use an existing patio but
if you wish to construct a new base for your spa, select
a level, flat area. After removing the topsoil, construct
a square frame using four 2x4's. Usually an area ten
square foot will suffice. When the frame has been
leveled, pour a 3 1/2" base of concrete mix into the
frame leveling the mix by stroking across the top with
another 2x4. Finish the top with the cement float.
When the slab has cured remove the 2x4's and
landscape as desired. Note: It is necessary to provide
drainage of the compartment for the electrical
components.
7. Install your spa in a location, which allows easy
access to the equipment bay.
8. Before filling with water, be sure the spa is in its final
position and that hoses, tools, etc. are not under the
spa.
Installation Instructions
Electrical-General
Prior to performing any service to the spa package
turn OFF ALL primary electric power at the main
circuit breaker or disconnect panel.
Opening the front cover of the electrical control box
can make all field electrical connections.
All electrical connections to this spa package must be
accomplished by a qualified electrician in accordance
with the National Electric Code or the Canadian
Electric Code and in accordance with any local
electrical codes in effect at the time of installation.
All connections should be made in accordance with
the wiring tab enclosed in the electrical control box.
These spa packages are designed to operate on 60Hz
Alternating Current only, at a voltage of 240 volts.
Spa packages with a 240-volt rating require a three
wire electrical service, plus ground (line 1, line 2,
neutral and ground).
Connections should be made using copper conductors
only. The connecting wire and circuit breakers or
fuses must be sized to accommodate the Total
Ampere load as specified on the equipment module
data label.
A bonding lug has been provided on the equipment
module to allow connection to local ground points. To
reduce the risk of electrical shock, a #8 AWG solid
copper bonding wire should be run from this lug to
any metal ladders, water pipes or other metal within 5
feet of the spa.
PLEASE NOTE: To Overseas
owners
50 Hz, 230-volt units should be wired
to the national code in the country of
the owner’s residence.
240 volt Installation
Units to be operated at 240 volts must have all electrical
connections accomplished by a qualified electrician in
accordance with the National Electric Code, the Canadian
Electric Code or other local electrical codes in effect at the
time of installation.
Equipment modules installed for 240-volt operation
requires a three wire electrical service, plus ground (line 1,
line 2, neutral and ground). Refer to terminal block
diagram.
Starting the Spa
1. Fill the spa to at least minimum water level (indicated
near the skimmer) before electrical power is turned on.
- Be sure all valves and hose bib, located on power
pack, are closed and all union nuts are tight.
2. Check for plumbing leaks.
3. Be sure all suction valves to the equipment pack are
open.
4. Open return valve with handle in up position.
5. Set filtering cycles according to control panel
instructions
.
4
