background image

5

6

Assembly Steps

BATTERY INFORMATION

Batteries may leak fluids that can cause chemical burn injury or ruin your product. To avoid battery leakage:

 Do not mix old and new batteries.

 Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). 

Insert batteries as indicated inside the battery compartment.

 Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. 

Battery leakage and corrosion can damage this product. Dispose of batteries safely. 

 Do not dispose of batteries in a fire. The batteries may explode or leak.

 Never short circuit the battery terminals.

 Non-rechargeable batteries are not to be recharged.

 Use only batteries of the same or equivalent type as recommended.

 If removable rechargeable batteries are used, the are only to be charged under adult supervision.

 Remove rechargeable batteries from the product before charging.

 Batter chargers used with toys must be examined regularly for damage to the cord, plug, enclosure and 

other parts. In the event that such damage is found, the toy must not be used with the battery charger until 

the damage has been repaired.

 When sound becomes faint or stops, it’s time to replace the batteries.

Ø10 

locknut

Ø10 

locknut

Ø10 

washer

Ø10 

washer

Front axle

Front hubcap

Front 

hubcap

Front 

wheel

 Remove one Ø10 locknut and one Ø10 

washer from the front axle with a spanner.

 Insert the tabs on the front hubcap into the 

slots in the front wheel. 

 Repeat this procedure to attach the other 

front hubcap to the front wheel.

 Fit and hold the front wheel to the front 

fork, and line up the holes in the front fork 

with the hole in the front wheel.

 Insert the front axle through the front fork 

and the front wheel.

 Slide a Ø10 washer onto the front axle, 

and fit a Ø10 locknut to the end of the front 

axle. Tighten the locknuts on both sides of 

front axle with two spanners. DO NOT over 

tighten.

 Remove the screw in the battery 

compartment door on the handle bar using 
a screwdriver and lift to open.

 Insert three “AA” (LR6) alkaline batteries 

as indicated inside the battery 
compartment.

  Replace the battery compartment door.

Note: This product does not Includ 
the “AA” (LR6) alkaline batteries.

Содержание 370-033


















Отзывы: