background image

www.qimaging.com

  

©2014 QImaging. All rights reserved.  QI_OPTIMOS_UM_Rev_A0 

4

optiMOS USER MANUAL

CHAPTER 2

INSTALLATION 

This chapter will detail the proper installation of your optiMOS camera. In order to install and use the camera, 
the following items are required:

 

optiMOS camera (supplied)

 

High Speed Data Cable (supplied)

 

High Speed PCIex4 Data Card

 

9V 8.33A power supply (supplied)

 

USB “installer” flash drive (supplied)

 

110V/220V power connection

 

A PC that meets the host computer requirements

Host Computer Requirements

The host computer for your optiMOS camera must include at a minimum:

 

Windows 7 operating system (64 bits)

 

2.0 GHz or faster Intel processor: either Xeon or Core i7

 

4+ GB RAM

 

250+ GB serial ATA (SATA) HDD and/or >64 GB solid state drive (SDD) for high-speed imaging and 
storage

 

256+ MB slot-based ATI/NVIDIA video graphics card (i.e., not an “onboard/integrated graphics” 
adapter)

 

USB drive or internet access to install the driver

 

At least 1 available PCIex4 slot

NOTE: Minimum requirements as of October 2013. Supported computer systems will change as new cameras, 
computer hardware, and operating systems are introduced and older models become obsolete. For current 
information on recommended computer specifications, please visit: 

http://www.qimaging.com/support/

recommended-computer-specifications.php

Содержание OptiMOS Series































Отзывы: