Q Imaging OptiMOS Series Скачать руководство пользователя страница 2

Страница: 2 / 30

www.qimaging.com

optiMOS USER MANUAL

Applicability

This document applies to the optiMOS camera. For the latest updates, please visit

www.qimaging.com

Notice of Copyright

Copyright © 2014 Quantitative Imaging Corporation. All rights reserved. Unauthorized duplication of this
document is prohibited.

Trademarks and Proprietary Names

optiMOS

™

is a trademark of QImaging. QImaging

and PVCAM

are registered trademarks of Roper Scientific,

Inc. Product names mentioned in this document may be trademarks or registered trademarks of QImaging or
other hardware, software or service providers, and are used herein for identification purposes only. Microsoft

and Windows

are registered trademarks in the U.S. and other countries of Microsoft Corporation and are

used herein for identification purposes only.

QImaging Corporation Address Information

19535 56th Avenue,
Suite 101
Surrey, BC, Canada V3S 6K3
604.530.5800

www.qimaging.com

QImaging Technical Support

Technical support is available to all registered users of QImaging products from 9am to 5pm Pacific
Standard Time.

[email protected]

800.874.9789

http://www.qimaging.com/support/contact

Содержание OptiMOS Series





























Результаты поиска

Содержание OptiMOS Series

Отзывы:

Похожие инструкции для OptiMOS Series

Бренды по названию

Популярные бренды

Q Imaging OptiMOS Series, Руководство пользователя

Результаты поиска

Содержание OptiMOS Series

Отзывы:

Похожие инструкции для OptiMOS Series

Бренды по названию

Популярные бренды