background image

As  always  the  final  settings  should  be  determined  by  listening.  You 

Switching On

should listen to a wide range of music at different volume settings while 

Check that all system connections are properly and securely made.

doing the setup.

Ensure that the subwoofer is switched off.

When setting up the subwoofer, always bear in mind that the human ear’s 

Set the subwoofer level control roughly halfway. Set the crossover control 

sensitivity to bass varies enormously with the volume level, hence the 

to 70Hz.

need for a wide range of programme material and sound levels.

Plug the supplied power cord into the subwoofer and then into the mains 
point.  Switch  on  the  power  at  the  mains  point  and  then  switch  the 

Phase: 

The phase switch should be initially set at 0º. As room acoustics 

ON/OFF  switch  on  the  subwoofer  to  ON.  The  POWER  light  on  the 

and  placement  are  important  at  very  low  frequencies  the  phase  may 

subwoofer rear panel will glow and  the subwoofer is operational.

need to be set to 180º. One setting will offer fuller and more extended 
bass than the other. As the effect can be quite subtle, especially with 

Setting Up and Use

small  loudspeakers  where  relatively  more  bass  is  coming  from  the 

As  there  is  a  close  relationship  between  the  subwoofer  volume,  its 

subwoofer, extended listening and experimentation may be necessary 

physical position and the crossover frequency, mutual adjustments to all 

before the final decision is made.

three  may be necessary before the system is fully set up.

Auto Power On:

 This feature enables you to switch the main system on 

Level: 

The Level Control sets the volume of the subwoofer relative to the 

and off without having to remember to switch the subwoofer on and off as 

other speakers in the system. Set a level that enhances the bass of the 

well.

system. There should be a seamless blend between the front speakers 

The 1000Si has a built in level sensor. If there is no input, after a short time 

and the subwoofer. If you can hear the subwoofer it’s too loud! 

the subwoofer will automatically power down into Standby mode. This is 

Crossover frequency: 

Set the crossover control according to the size 

indicated by the POWER light on the rear panel changing to red. As soon 

and  low  frequency  extension  of  the  front  speakers.  The  role  of  the 

as  the  subwoofer  senses  an  input  it  will  automatically  switch  into 

subwoofer  is  to  extend  the  bass  response  of  the  system  and  not

 

to 

operational mode and the power light will again glow green.

increase  the  overall  bass  level.  If  the  loudspeakers  are  large,  a  value 

Although  the  subwoofer  can  be  safely  be  left  in  standby  mode 

between 50 and 60 Hz is probably about right. With smaller speakers 

indefinitely, if you are going to be absent from home for a long period, we 

such as the 1010i, this can be increased as far as 90Hz. At higher settings 

advise that the unit be switched off at the ON/OFF switch.

the subwoofer may become intrusive and low level detail and definition 
may suffer. 

1000i Subwoofer - Operation

Содержание 1000i SERIES



















Отзывы: