background image

13 

+12VDC-

 Pin 1 (Yellow wire) on the 

Hard Drive connector.  

12 VDC acceptor power.

Communication Ground- 

Pin 5 (Black 

wire) on the DB-9 connector. 

DC communication ground.

TXD Line-

 Pin 3 (Green wire) on the 

DB-9 connector. 

Connected to TXD line from your PC. (PC TXD line) 

RXD Line-

 Pin 2 (White wire) on the 

DB-9 connector. 

Connected to RXD line from your PC. (PC RXD line) 

 
MDB Mode of Operation 

Note: To enable this mode on the acceptor, make sure the Configuration Card has 
been configured for “MDB” mode. Our MDB interface uses the standard MDB 
connector (see Below) for communication. 

 
 

 
MDB Mode Power and I/O Connections 

 

Pin Location 

Pin Description

Pin 1 

+34 VDC Power

Pin 2 

DC power return

Pin 3 

Not used

Pin 4 

Master Receive

Pin 5 

Master Transmit

Pin 6 

Communications Common 

 
Parallel Mode of Operation 

Note: To enable this mode on the acceptor, make sure the Configuration Card has been 
configured for “Parallel” mode. The Parallel mode is compatible with the Innovative 
Technologies™ “Smiley™ bill acceptor.                 
In this mode, a single output is applied to one of four Vend lines to show which bill has been 
accepted. This allows you to have up to four denominations of bills to be accepted. Also provided 
in this interface is an Alarm line to indicate an abnormal condition. An Escrow line is also provided 
to allow more control over which bill is accepted by the Apex bill acceptor. 

This mode can be used in our 12 VDC models as well as our 120 VAC and 24 VAC models. 

Interface Operation 

The Inhibit line is used to enable the Apex bill acceptor. Pull it low to enable the acceptor, high to 
disable. The Alarm output will go low for 100 msec to signal an abnormality or error. A Vend Line 
will go low for 100 msec when a particular bill is recognized. Vend Lines 1-4 correspond to US bills 
$1, $5, $10 and $20. If the Escrow Line is not held low, the acceptor will accept a bill and send the 
appropriate signal via the Vend Line. If the Escrow Line is held low and a bill is inserted, the Apex 
bill acceptor will send out a “Credit” signal telling you what the value of the bill is (by toggling the 
appropriate Vend Line). If the Escrow Line is not brought high or the Inhibit Line goes high during 
a 30-second period, the bill will be rejected. If the user brings the Escrow Line high (and leaves the 
Inhibit line low) during the 30 second period, the acceptor will accept the bill and send out a “Vend” 
signal on the appropriate Credit Line. The Vend signal will not be issued if the bill jams or a 
“Stealing” attempt is seen by the acceptor. In this case, the bill will be rejected and the acceptor 
will toggle the Alarm Line. 

 
Parallel Mode Power and I/O Connections (Refer to Figure 1 for Pinouts) 

Pin Function & Location 

Apex 12VDC Version 

Apex 120 VAC or 24 VAC Version 

DC Ground-

 Pin 4 (Black wire) on the 

18-pin

 connector. 

DC communication ground and 
DC power ground. 

DC communication ground 

+12 VDC-

 Pin 11 (Red wire) on the 

18-

pin

 connector. 

12 VDC acceptor power 

Do not use this pin for 120 VAC 
version. 

Содержание APEX 5000 Series


















Отзывы: