manualshive.com logo in svg

PVI Industries CONQUEST 20 L 100 A-GCL, Инструкция по установке и обслуживанию

Поделиться
Скачать
PVI Industries CONQUEST 20 L 100 A-GCL Скачать руководство пользователя страница 24

CONQUEST

® 

WATER HEATER

 

24 

PV500-70  10/15

 

WARNING: Do not connect multiple water heaters vents into a single unpowered or fixed speed powered 
vent. This could cause unsafe operation and the potential for poisonous carbon monoxide to enter occupied 
areas. Such improper installation can cause property damage, exposure to hazardous materials, personal 
injury or death. 

 
Conventional Venting 

Through the Wall Venting 

Combining Vents with a Draft Inducer 

 

 

 

 

8.5  Optional Concentric Vent for Combustion Air and Exhausting Flue Products 

To provide a single sidewall or roof penetration that is capable of providing both combustion air and flue exhaust 
termination, each Conquest water heater must be installed using an IPEX System 636

TM

 Concentric Vent 

Termination Kit. Both the IPEX System 636

TM

 PVC and CPVC Flue Gas Venting Systems are third party tested and 

listed to ULC S636 and comply with the non-metallic vent listing requirements in CAN/CSA B149.1-10 Natural Gas 
and Propane Installation Code. 

The following IPEX System 636

TM

 Concentric Vent Termination Kits are available through PVI for Conquest water 

heaters: 

PVI Part No. 

Description 

122555 

KIT,VENT CONCENTRIC  4  PVC      IPEX #196021 for PVC (4" x 36") 

122367 

KIT,VENT CONCENTRIC  4  CPVC   IPEX #197021 for CPVC (4" x 36")   

124574 

KIT,VENT CONCENTRIC  3  PVC      IPEX #196106 for PVC (3" x 32") 

127319 

KIT,VENT CONCENTRIC  3  CPVC   IPEX #196107 for CPVC (3" x 32") 

 

Each IPEX System 636 vent kit includes or specifies the required pipe, fittings, hardware, adhesives and Installation 
instructions. Follow the IPEX Installation instructions and use only the materials and adhesives it specifies. Additional 
copies of the Installation Guide for the IPEX System 636 concentric vent kit and additional information is available at 

www.ipexinc.com  or  www.pvi.com/vent-design.html

. 

When using concentric vent termination kits, all combustion air duct, all exhaust vent pipe and the IPEX concentric 
vent kit material types must be the same. If the Conquest is installed with a PVC exhaust vent pipe, then the 
combustion air duct and the IPEX concentric vent kit must also be made of PVC. If the Conquest is installed with a 
CPVC exhaust vent pipe, then the combustion air duct and the IPEX concentric vent kit must also be made of CPVC. 

WARNING: Follow the Installation instructions provided with the listed IPEX Concentric Vent Kit, using only 
the pipe, fittings and cement included or specified in the IPEX installation instructions. Failure to follow the 
IPEX installation instructions or to use pipe, fittings or cement not included or specified in the IPEX 
installation instructions could result in an unreliable vent assembly or installation that can cause the 
potential for hazardous products of combustion to enter occupied areas and can cause property damage, 
exposure to hazardous materials, personal injury or death. 

Содержание CONQUEST 20 L 100 A-GCL





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды