PVA B12-2235 Скачать руководство пользователя страница 4

Periodic Maintenance 
 

Refer to the FCM100 cross sectional view for location of parts referenced in the 

following procedures. 
 

1)

 

Lubricate the packing (5) on the FCM100 valve every 200 hrs by placing a few 
drops of mineral oil or other light oil inside the packing nut.  
*Note: PVA offers a 2.5cc mineral oil lubrication kit; Part#: B62-0752 

2)

 

The packing nut (6) may require occasional tightening, as wear occurs in order to 
prevent leaks through the packing. 

 

 

 

Setup 

 

The FCM100 requires a 2-position, 4-way air solenoid  valve to actuate the air 

section.  The valve should be operated with clean, dry air between 60-100psi. Two #10-32 
threaded air ports are located on the air section of the valve. The port located furthest 
from the midsection of the valve is air to close the valve. The port located closest to the 
mid-section of the valve is air to open the valve. Quick connect air fittings are typically 
supplied with the FCM100 to fit 5/32” tubing.  Note that the valve should be normally in 
the closed position. 

Fluid is supplied to the FCM100 through the 1/8”fnpt port located on the stainless 

steel fluid section of the valve.  

 

 

 

 

Содержание B12-2235













Отзывы: