PVA B12-2235 Скачать руководство пользователя страница 3

 

Nozzle Options 

 

The FCM100 valve is available with several different gauge size dispense nozzles 

(17). Different nozzle sizes are easily interchangeable to the valve by removing the 
nozzle lock nut (12). Nozzle sizes are selected based on the size dot or bead of material 
that is to be applied. A 22 gauge nozzle will give you the largest dot and wider bead 
width while the 30 gauge nozzle will offer the smallest dot size and smallest bead width. 

Valves are supplied from the factory with one nozzle included. Below is a chart 

showing part number that are used to specify the nozzle that is supplied with a valve, the 
available gauge sizes, inside diameters of the nozzles, and part number for each 
individual nozzle.  

 

 

Valve Part Number              Nozzle Size              Nozzle ID              Nozzle Part Number 

 

FCM100-22G  

         22 gauge                  0.016” 

 

PV-22005A 

FCM100-25G  

         25 gauge  

     0.010” 

 

PV-25007A 

FCM100-27G  

         27 gauge  

     0.008” 

 

PV-27005A 

FCM100-28G  

         28 gauge  

     0.007” 

 

PV-28004A 

 

FCM100-30G  

         30 gauge  

     0.006” 

 

PV-30001A 

 

 

 

 

 

Safety 

 

Due to material contents being under pressure eye protection is required for 

operators. Refer to MSDS sheets on material being dispensed for other precautions.

 

 
 
 
 
 
 
 
 
 
 

Содержание B12-2235













Отзывы: