PVA 112-2190 Скачать руководство пользователя страница 7

 

FCS300 Series Manual 

 

Revision D 

/

 June 2020 

Page 7 of 34 

 

 

Safety 

Due to material contents being under pressure, eye protection is required for operators. All 
spray valves should be used in a well-ventilated area. For additional precautions, refer to 
the MSDS sheet for the dispensed material. 

 

Setup 

The FCS300 Series requires a 2-position, 4-way air solenoid valve to actuate the air 
section. The valve should be operated with clean, dry air between 60-100psi. Two #10-32 
threaded air ports are located on the air section of the valve. The port located furthest from 
the midsection of the valve is air to close the valve. The port located closest to the mid-
section of the valve is air to open the valve. Quick connect air fittings are typically supplied 
with the FCS300 Series to fit 5/32” tubing.   

Note: The valve should normally be in the closed position. 

Atomizing air is connected to the #10-32 threaded port located on the fluid section. Quick 
connect air fittings are typically supplied to fit 5/32” tubing. Atomizing air should be 
connected such that it turns on only when the valve is cycled to the open position. There 
are two configurations that can be used to connect atomizing air. The first configuration 
uses a Single Solenoid with a one output used to simultaneously open the valve and 
pressurize the atomizing air regulator. The second option uses a Dual Solenoid 
configuration to allow independent control of the atomizing air.   

Fluid is supplied to the FCS300 Series through the 1/8”fnpt port located on the stainless 
steel fluid section of the valve. 

Содержание 112-2190



































Отзывы: