PV Electronics Spectrum 1040 Скачать руководство пользователя | Manualshive

Страница: 12 / 39

background image

Nixie Tube Clock ‘Spectrum 18 / 1040’

Issue 7 (15 June 2018)

www.pvelectronics.co.uk

- 12 -

4.4

Low Voltage Generator components.
Fuse
D1, D2, D3 (1N5819)
C1, C2 (220uF)
J1 (12V IN), L1
IC1 (LM2576)

Depending on the fuse you have been supplied with, the leads may
not fit through the holes. If this is the case, simply wet the 2 pads
with solder and pre-cut the fuse leads very short. Solder the fuse
leads onto the top of the two wetted pads.

Bend the legs of IC1 to a 90 degree angle so that the component
lies along the PCB. Solder it so it does not quite touch the PCB. But
is approx 2-3 mm from it. (1/8”)

C1 and C2 are polarized. The light stripe on the body of the
component indicates the negative side. This must match the cross
hatched side on the PCB Marking.

Please note that J1 and L1 must be soldered on the bottom
of the PCB in all cases.

«
...
10
11
12
13
14
...
»

Содержание Spectrum 1040








































Отзывы:

Нет отзывов

Похожие инструкции для Spectrum 1040

Бренд: Kambrook Страницы: 2

Бренд: Hama Страницы: 75

Бренд: Timex Страницы: 24

Бренд: GPX Страницы: 2

Бренд: Lenoxx Страницы: 7

Бренд: Dakota Digital Страницы: 4

Бренд: Goodmans Страницы: 15

Бренд: MP-Man Страницы: 5

Бренд: Denver Страницы: 1

Бренд: ADE Страницы: 134

Бренд: Manta Страницы: 30

AVENGERS RP500AV

Бренд: LEXIBOOK Страницы: 34

Бренд: HumanTechnik Страницы: 40

Бренд: La Crosse Страницы: 4

Бренд: Konig Страницы: 27

Бренд: Clas Ohlson Страницы: 5

Бренд: Krown Страницы: 20

Бренд: Konig Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды