PureTools PT-PSW-21C Скачать руководство пользователя страница 12

Страница: 12 / 36

User Manual

PT-PSW-21C

Press

to increase the audio volume gradually, or press and hold it to

increase the audio volume constantly.

④

EDID:

4-pin DIP switch for EDID setting.

⑤

FW:

Micro-USB port for firmware upgrade.

3.2

Rear Panel

①

HDMI IN:

Type-A female HDMI input port to connect HDMI video source.

②

USB-C IN:

Type-C USB with charging capability to connect the Macbook or other

device with SlimPort output.

Note:

The USB 3.0 cable is recommended to be used to ensure optimal machine

performance.

③

HDMI OUT:

Type-A female HDMI output port to connect video display.

④

AUDIO OUT:

5-pin terminal block for balanced audio output.

⑤

RS232:

3-pin terminal block to connect control device (e.g. PC) or third-party

device for RS232 control.

⑥

HOST:

Type-B USB ports for host connection.

⑦

DEVICES:

Two type-A USB ports to connect HID devices (e.g. microphone and

camera). The HID devices are used to control the HOST when the HDMI input has
been selected, or to control the USB-C source device (e.g. Macbook) when the
USB-C input has been selected.

⑧

DC 24V:

DC barrel port for power adapter connection.

HDMI IN

USB-C IN

HDMI OUT

AUDIO OUT

DEVICES

RS232

HOST

DC 24V

Содержание PT-PSW-21C




































Результаты поиска

Содержание PT-PSW-21C

Отзывы:

Похожие инструкции для PT-PSW-21C

Бренды по названию

Популярные бренды

PureTools PT-PSW-21C, Руководство пользователя

Результаты поиска

Содержание PT-PSW-21C

Отзывы:

Похожие инструкции для PT-PSW-21C

Бренды по названию

Популярные бренды