background image

 

 

PULSAR

 

ULTRA SERIES 

SLUDGE FINDER 2 SERVICE MANUAL

 

(FIRST EDITION Rev 2) 

June 2017 

Part Number M-920-S-001-1P 

C

OPYRIGHT

 

© Pulsar Process Measurement Limited, 2000 – 17. All rights reserved. No part of this

 

publication may be 

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form 
without the written permission of Pulsar Process Measurement Limited. 

W

ARRANTY AND 

L

IABILITY

 

Pulsar Process Measurement Limited guarantee for a period of 2 years (for the integrator), and 1 year (for the 
transducer), from the date of delivery that it will either exchange or repair any part of the product returned to 
Pulsar Process Measurement Limited if it is found to be defective in material or workmanship, subject to the 
defect not being due to unfair wear and tear, misuse, modification or alteration, accident misapplication or 
negligence. 

D

ISCLAIMER

 

Pulsar Process Measurement Limited gives nor implies any process guarantee for the product, and shall have 
no liability in respect of any loss, injury or damage whatsoever arising out of the application or use of any 
product or circuit described herein. 

Every effort has been made to ensure accuracy of this documentation, but Pulsar Process Measurement 
Limited cannot be held liable for any errors. 

 

T

ECHNICAL

 E

NQUIRIES

 

Please contact Pulsar Process Measurement Limited for technical support. 

C

OMMENTS AND

 S

UGGESTIONS

 

If you have any comments or suggestions about this product, then please contact: 

 

Pulsar Process Measurement Limited 

Cardinal Building 

Enigma Commercial Centre 

Sandy’s Road 

Malvern 

Worcestershire 

WR14 1JJ 

United Kingdom 

Tel: 01684 891371 (

Interna44 1684 891371)

 

Fax: 01684 575985 (

Interna44 1684 575985)

 

Web Site: http://www.pulsar-pm.com 

e-mail: [email protected] (general information) 

e-mail: [email protected] (product support) 

Содержание M-920-S-001-1P


































Отзывы: