Instructions
Pulsar Light of Cambridge Limited
●
3 Coldhams Business Park
●
Norman Way
●
Cambridge
●
CB1 3LH
●
England
●
Tel: 44 (0)1223 403500
●
Fax: 44 (0)1223 403501
●
Email: sales@pulsarlight.com
●
Web: www.pulsarlight.com
CFLD100
- ChromaFlood100 – 5,8,25,45,12x25,10x90
lenses
CFLD200
- ChromaFlood200 – 8,25,45,12x25,10x90 lenses
CBAT100
- ChromaBatten100 – 10, 25 and 45 degree lenses
CBAT200
- ChromaBatten200 – 10, 25 and 45 degree lenses
CBAT300
- ChromaBatten300 – 10, 25 and 45 degree lenses
The
ChromaFlood
and
ChromaBatten
contain state of the art, high
brightness, high efficiency Red, Green and Blue LEDs. These three
primary colours can be mixed together to make an incredible palette
of 16.7 million colours.
They are IP65 rated fixtures and therefore suitable for outdoor or
indoor use. They are powered directly from 100-240 Volts AC and
have full remote DMX control of RGB levels or can function in Stand
Alone Mode. Numerous chases and sequences are built in, enabling
superb lighting effects without complicated programming.
These impressive fixtures are ideal for the architectural and
entertainment markets to give an unlimited colour palette that can
enhance building facades, water features and focal displays or to
providing stunning dynamic colour in shows, conferences, concerts
and themed environments.
Like the
ChromaBank,
the
ChromaFlood and ChromaBatten
contain a
PULSAR ChromaZone
controller and can therefore also
operate in 3, 6, 9, 10, 36, 42 or 46 Channel Modes.
It is useful to consider the
ChromaFlood
as being 1 of the 12
fixtures, and the
ChromaBatten
as being, either 1 or 3, of the 12
fixtures, within a
ChromaBank
.
Please see the
Channel Assignments Tables
sheet for details of
the different modes.
The
ChromaFlood and ChromaBatten
have numerous chases and
effects built in, making it possible to achieve fantastic effects without
programming. These internal effects can be selected via the
User
Interface Module
(UIM) on the rear of the units whilst in Stand Alone
mode, or from a controller using a digital
PMX
(
P
ulsar
M
ultiple
X
) or
DMX
(
D
igital
M
ultiple
X
) signal.
Please see the
Menu Selection Overview
sheet for a pictorial
representation of the menu functions.
The
ChromaFlood and ChromaBatten
have mounting brackets
making them ideal for floor, wall, ceiling or rig mounting.
The
ChromaFlood
picture at the top of this page shows the
mounting brackets arranged for floor mounting.
ChromaFlood and ChromaBatten
have a colour code letter. This
signifies the finished colour of the fixture (B = Black, S = Silver). Other
colours may become available - please check with Pulsar if required.
The
ChromaFlood and ChromaBatten
have a thermal
management system. This progressively reduces the power to the
LEDs if the internal temperature exceeds limits set by the software.
Excess temperature will occur if the units are exposed to high
ambient temperatures or inadvertently covered. It is therefore
important for maximum performance that they have good ventilation
on all sides.
The lenses shipped with the
ChromaFlood and ChromaBatten
may be easily changed. Currently 5 (ChromaFlood100 only), 8, 25,
45, 12x25 (elliptical) and 10x90 (elliptical) lens plates are available for
the
ChromaFlood
with 10, 25 and 45 degree lenses available for the
ChromaBatten
.
Other lenses may become available, please contact
Pulsar
or see
www.pulsarlight.com
for details
NB - Patents applied for
Mains Supply
- The
ChromaFlood and ChromaBatten
work
correctly on any mains voltage from 100-240 VAC, 50-60Hz, (self
adjusting). Power consumption is 200 Watts max.
A 5m, bare ended, mains cable is provided. The bare end of the
cable should be fitted with a suitably approved and rated mains plug.
Note: in some countries it is a requirement that such a plug be fitted
by a qualified electrician.
CABLE COLOURS
Green/Yellow =
Earth / Ground
Brown = Live / Phase / Hot
Blue = Neutral
WARNING - THIS APPLIANCE MUST BE EARTHED
For safety we recommend the use of a Residual Current Circuit
Breaker. An RCCB MUST be used when powering a
ChromaFlood or ChromaBatten in wet environments.
PMX/DMX In/Thru 5 Pin XLR Connectors
Digital Control Signals:
Two 5 pin XLR connectors on 5m cables
(in/thru) are provided. The pin connections of the sockets are:
PMX (RS232/423) SIGNAL
DMX SIGNAL
Pin 1 = Screen / Chassis Earth
Pin 1 = Screen / Chassis Earth
Pin 2 = Signal
(Blue)
Pin 2 = Signal
-
Pin 3 = Signal Earth
(White)
Pin 3 = Signal
+
Pin 4 = no connection
(Green) Pin 4 = no connection
Pin 5 = LVS (male only)
(Red)
Pin 5 = LVS (male only)
Wet / Damp Environment Use
– these products are IP65
rated. However, the cable connections
must
also be
contained in a dry, low humidity, environment as water and
vapour will travel inside the cables from the connection joints into the
fixture. A waterproof connection box, or properly fitted IP68 rated
connectors, are essential for cable connections in such
environments. Suitable connectors are available from Pulsar.
Failure to take these precautions invalidates the guarantee.
CONNECTIONS
SPECIFICATION
SPECIFICATION
CHROMAFLOOD
CHROMABATTEN