Pulsafeeder PULSAR Shadow Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 46

background image

13

5.1 Oil Capacities

Pulsalube 9M lubricating oil is available in 950 ml (1 quart) containers.

Pulsalube 8G gear oil is available in 200 ml (.21 quarts) or 950 ml (1 quart) containers.

It is recommended that adequate supplies of both PULSAlube oils be on hand for
periodic changes and emergency requirements. The approximate amounts of oil
required to fill PULSAR Shadow® pumps to specified levels are:

Eccentric Box, all

Gearbox, Model 25B Gearbox, Model 55B

Eccentric Oil, No. 9M

950 ml (1 Qt)

--

--

Gear Oil, No. 8G

--

150 ml (0.16 Qt)

200 ml (0.21 Qt)

5.2 Eccentric Oil Fill

Fill the eccentric box with oil by removing the manual cover assembly or DLC/M or ECA
controller if so equipped. Fill with the proper oil (Pulsalube 9M) to the upper edge of the
crosshead assembly and return spring(s) or slightly above. Replace the cover or
controller. Take care not to disturb the stroke length setting when reinstalling. See
figure 12.

Figure 12

5.3 Gear Oil Fill

In all pump configurations, one pipe plug is present at the top of the gearbox and one is
on the side at the centerline level. Remove the top plug and fill with Pulsalube 8G gear
oil through the top port to the level of the eccentric shaft centerline, which is level with
the side port. The side plug should be removed so that leakage from the side port
indicates attainment of the required level. Replace both pipe plugs after filling.

GEAR OIL IS FILLED AT THE FACTORY, AND THE GEARBOX IS SHIPPED FULL.

DO NOT ADD OIL THROUGH THE PORT ON THE SIDE OF THE MOTOR ADAPTOR.
THIS PORT IS FOR MOTOR COUPLING ACCESS ONLY.

«
...
16
17
18
19
20
...
»

Содержание PULSAR Shadow Series















































Отзывы:

Нет отзывов

Похожие инструкции для PULSAR Shadow Series

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: GEA Страницы: 78

Бренд: Waterous Страницы: 10

Бренд: York Страницы: 27

Бренд: York Страницы: 32

Бренд: Bard Страницы: 26

SWUP EXT Series

Бренд: Sunsystem Страницы: 16

Бренд: DAYLIFF Страницы: 12

Бренд: AMICOCIRC Страницы: 13

Corken Z-Series

Бренд: Idex Страницы: 32

Бренд: T.I.P. Страницы: 112

Бренд: Kärcher Страницы: 50

Бренд: Thermor Страницы: 56

Бренд: NAKAYA Страницы: 47

Бренд: Samoa Страницы: 40

Бренд: Little Giant Страницы: 40

Бренд: Espa Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды