background image

3

This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting 

steps described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest 

product information available at the time of publication. The manufacturer reserves the right to make product changes at any time 

without notice. 

SAFETY GUIDELINES / DEFINITIONS

UNPACKING AND INSPECTION

WARNING: Read and understand this entire instruction manual before attempting to assemble, install, operate or maintain 

this product. Failure to comply with the instructions may result in serious personal injury and/or property damage!
The following signal words are used to emphasize safety warnings that must be followed when using this product:

DANGER: Indicates an imminently hazardous situation 

that, if not avoided, WILL result in death or serious injury.

WARNING: Indicates a potentially hazardous situation that, 

if not avoided, COULD result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation that, 

if not avoided, MAY result in minor or moderate injury.

NOTE: Indicates important information, which if not 

followed, MAY cause damage to equipment.

After opening the carton, unpack your new product and related parts and accessories. Please 

inspect it carefully for any damage that may have occurred during transit. Please check it against 

the package contents on page 4. If any parts are missing, please call customer service at 1-800-

426-1262 between 6 a.m. and 5 p.m. Pacific time. 

WARNING: DO NOT operate this product if damaged during shipment, handling or misuse.  

Do not operate the product until the parts have been replaced or the fault rectified. Failure to do 

so may result in serious personal injury or property damage. All damaged parts must be repaired 

or replaced as needed prior to operating this product. Check to see that all nuts, bolts and fittings 

are secure before putting this product into service. 

If you have any questions, or require assistance with damaged or missing parts, please contact 

our customer service department at 1-800-426-1262. Please have the serial number, model 

number, and date of purchase available for reference when calling.

PRODUCT WARNINGS

•  Failure to heed these warnings may result in loss of load, damage to lift, and/or lift failure 

  resulting in personal injury or property damage.

•  This is a lifting device only. Load must be supported immediately by Safety Bar and other 

  appropriate device.

•  Do not overload lift beyond rated capacity. Overloading can cause damage to or failure of the lift.

•  Refer to LIFTING PROCEDURES IN THE owners manual FOR THE ITEM YOU ARE 

  LIFTING. Lift only on areas as specified by the manufacturer.

•  This lift is designed for use only on hard level surfaces capable of sustaining the load. Use of 

  lift on other than hard level surfaces can result in lift instability and possible loss of load.

WARNING: NEVER ATTEMPT TO RAISE THE LIFT WHILE THE TIE DOWNS ARE 

ATTACHED TO THE LOAD.

•  Leveling bolts are intended to fix the unit to the ground and avoid movement while lifting a 

  load. DO NOT use them as stabilizers.

•  USE included straps to secure the load to the lift.

•  ENSURE the safety levers are engaged when load is raised to prevent accidental lowering.

•  DO NOT make any alterations to this product.

•  LOWER LIFT as much as possible before moving lift while supporting a load.

•  KEEP FINGERS, HANDS AND FEET AWAY from the lift arms and other moving parts.

•  NEVER lift the load without first assuring that it is properly balanced and secure on the lift.

Содержание W41035











Отзывы: