PT AMC131 Скачать руководство пользователя

Страница: 48 / 108

Chapter 4: Connectors

200-pin SDRAM Sockets (P6, P7)

For information on memory compatibility, see

“SDRAM,” on page 25

Note: Memory is not a field serviceable item. Return the module to PT for memory
replacement. See

“Return Merchandise Authorization (RMA),” on page 19

for more information

about returning merchandise.

Battery Socket (BT1)

See

“Real-time Clock with Battery Backup,” on page 29

for information on battery compatibility.

Note: The battery is not a field serviceable item. Return the module to PT for memory
replacement. See

“Return Merchandise Authorization (RMA),” on page 19

for more information

about returning merchandise.

MiniSD Card Connector (P1)

MiniSD card support is provided via a miniSD card socket located on the board. See

“Global

Storage,” on page 25

for more information. See

“Working with the MiniSD Card,” on page 35

for

information about miniSD card installation and removal.

Payload Processor IMC Connector (P2, P3)

The payload processor in circuit emulator is accesses through connectors P2 and P3.

Table

4-6

provides the pinout.

Table 4-6:

Payload Processor ICE and JTAG PCB Connector Pinout

P3 PIN

NET

Pin Function on the Module

CPU1_TDO

CPU1 Test Data Out

CPU1_TDI

CPU1 Test Data In

COP_RUN_STOP_N

Common On-Chip Debugger (COP) Software Run/Stop

CPU1_TCK

CPU1 Test Clock

CPU1_TMS

CPU1 Test Mode Select

COP_SRST_N

Common On-Chip Debugger Software Reset

COP_HRST_N

COP Hardware Reset

CPU1_CKSTPO_N

CPU1 Checkstop Out

P2 PIN

No Connect

COP_TRST_N

COP Test Reset

V3P3_COP_VDD_SENSE

Ensures that the COP is aware whether 3.3V power is applied to
the module

CPU1_CKSTPI_N

CPU1 Checkstop In

ICE_EN_N (connect to GND)

In Circuit Emulator Enable

GND

Logical Ground

No Connect

GND

Logical Ground

Содержание AMC131













































































































Результаты поиска

Содержание AMC131

Отзывы:

Похожие инструкции для AMC131

Бренды по названию

Популярные бренды

PT AMC131, Руководство по оборудованию

Результаты поиска

Содержание AMC131

Отзывы:

Похожие инструкции для AMC131

Бренды по названию

Популярные бренды