Psion Teklogix OMNii HDK XT10 Скачать руководство пользователя | Manualshive

Страница: 165 / 192

background image

Chapter 10: HDK Demo Application

Main Tabs

Psion Teklogix Omnii HDK User Manual

155

This informs the user that the function of the pins will be changed from UART to GPIO operation,
to conform with the tab being selected. Tap on

OK

to continue on to the GPIO tab, or

Close

(

X

) to

remain on the current tab and leave the pins configured for UART operation.
After tapping

OK

, the following warning message appears:

Since UART and GPIO devices share the same data communication pins, the breakout board must
also be configured so that the pins are routed to the proper circuits on the board. This configuration
is done by jumpers on the breakout board, and is described in Chapter 9: “Breakout Board”.
Ensure that the jumper settings are correct, and tap

OK

to proceed.

10.6.2.4 EEPROM

The EEPROM tab provides an interface to read and write device information to the 1-wire
EEPROM on the expansion device.
This procedure does not require any drivers to be loaded, so you can use the HDK Demo
application to program the EEPROM even before configuring anything else (registry keys, etc.).
Ignore any error messages regarding drivers in this case.

Note: When connecting to the breakout board, the 1-wire EEPROM on the breakout board is

used,

not

the EEPROM of any device connected to the breakout board.

Ensure that the information stored in the EEPROM of the breakout board is correct and
matches the information in the EEPROM of the device being tested .

Data Fields

File Controls

EEPROM Controls

«
...
163
164
165
166
167
...
»

Содержание OMNii HDK XT10

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMNii HDK XT10

Бренд: Handspring Страницы: 2

Бренд: NEC Страницы: 56

Бренд: NEC Страницы: 4

Бренд: Samsung Страницы: 38

Бренд: Elo TouchSystems Страницы: 4

Бренд: Unitech Страницы: 85

Бренд: Trium Страницы: 66

Бренд: Honeywell Страницы: 16

Бренд: Datalogic Страницы: 2

Бренд: ITWell Страницы: 28

Бренд: M3 Mobile Страницы: 12

WORKABOUT PRO 7527C-G2

Бренд: Psion Teklogix Страницы: 446

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды