Psion Teklogix OMNii HDK XT10 Скачать руководство пользователя | Manualshive

Страница: 138 / 192

background image

Chapter 9: Breakout Board

Connecting to Omnii

128

Psion Teklogix Omnii HDK User Manual

5. Gently lift the back cover from the main housing to allow access to the cables that are

still attached.

6. Disconnect any cables attaching the back cover to the main unit (trigger switch, scan-

ner/imager, speaker, camera, GPS antenna are all possibilities).

7. Remove the back cover module.
8. Connect one end of the cable to the expansion port you wish to use (see Section 6.4:

“Expansion Ports” for details on connecting to these ports).

9. If the expansion back cover is used, run the cable through the end-cap or pod openings

and reattach the back cover for stability and security while testing.

10. Connect the other end of the cable to socket J33 or J42 on the breakout board.

11. Power Omnii on.
12. Load and run the required software for testing the expansion device.

Attach the Omnii Back Cover

When you are finished with your testing, follow these steps to re-attach the back cover to
your Omnii.
1. Connect all cables from the back cover to the main logic board (trigger/speaker, camera, etc.).
2. Fit the back cover in place on the main housing, making sure no cables are caught in

the seal. If a pod expansion module is required, fold the flex cable so that it is accessible
through the pod opening in the expansion back cover.

Warning: Exercise extreme caution if operating Omnii with the back cover removed. The unit

may be damaged if anything makes contact with the exposed circuitry while it is
powered on.

Warning: Zero- and low-insertion force connectors such as J33 and those on the Omnii

main

logic board are not designed to withstand many cable insertion/removal cycles and
may be damaged by repeated use. It is highly recommended to use socket J42 to
connect to the hand-held computer.
Also, when breaking the connection from the hand-held computer

,

disconnect the

cable from the breakout board rather than from the Omnii whenever possible.

Note: The breakout board will not work with the end-cap expansion port (Expansion Port 1) on

Omnii XT10 computers with main logic boards prior to revision “-500”.

«
...
136
137
138
139
140
...
»

Содержание OMNii HDK XT10

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMNii HDK XT10

Бренд: M3 Mobile Страницы: 30

Бренд: M3 Mobile Страницы: 14

Бренд: Nab Страницы: 88

Бренд: Zyteq Страницы: 2

Бренд: OBM Страницы: 8

Бренд: Unitech Страницы: 10

Pocket LOOX C Series

Бренд: Fujitsu Siemens Computers Страницы: 61

Бренд: TEL-TRU Страницы: 25

Бренд: Dolphin Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды