background image

Using the Cyclone

1. Roll the cyclone to the proximity of your machine.
2.  Connect the 6” hose to your machine port – adapt down to 4”, if necessary, with an appropriate  

6” to 4” adapter.

3. Close the 4” recirculation blast gate to the bottom of the filter.
4.  Open the blast gate to your machine and turn on the cyclone – never turn on the cyclone with all of 

your gates closed. 

5.  Dust will collect in the fiber drum. Check dust level periodically to make sure it is not more than half 

full. Empty the drum when more than half full. Note: a drum that is too full will result in debris  
continuing to clog up the canister.

6.  Clean the filter cartridge periodically by using compressed air (or a shop vac in reverse) to blow any 

dust off the internal pleats of the filter media.

7. Using the recirculation system:
 

• Close the gates to the cyclone main intake.

 

•  Open the gate under the funnel reducer. Turn on the cyclone while blowing the filter cartridge 

with air. The ambient dust from the filter will settle in the collection drum. 

 

• Close the blast gate under the filter before using the cyclone for normal dust collection..

COMPONENTS

NO DESCRIPTION 

QTY

1  CASTER 

4

2  M12 NUT 

12

3  12mm WASHER 

4

4  12mm LOCK WASHER 

4

5   BASE PLATE 

1

6  LONG VERTICAL SUPPORT  2
7  SHORT VERTICAL SUPPORT  2
8   MID HORIZONTAL SUPPORTS  

(FRONT & BACK) 

2

9   MID HORIZONTAL SUPPORTS  

(LEFT & RIGHT) 

2

10   TOP HORIZONTAL SUPPORTS 

(MAIN CYCLONE SUPPORT)  3

11  LEFT BRACKET 

1

12  CANISTER HOOK 

2

13  BRACKET ARM 

2

14  8mm WASHER 

43

15  M8 NUT 

43

16  RIGHT BRACKET 

1

17  8mm LOCK WASHER 

39

18  M8X20 CARRIAGE BOLT  39
19  SWITCH SUPPORT 

1

20  5mm WASHER 

2

21  M5X16mm PHILLIP SCREW 2
22  SWITCH WITH FACE PLATE  1
22a SWITCH BOX 

1

47  M3X16 PHILLIP SCREW 

2

48  POWER CORD 

1

NO DESCRIPTION 

QTY

14  8mm WASHER 

4

15  M8 NUT 

4

17  8mm LOCK WASHER 

4

18  M8X20 CARRIAGE BOLT 

4

25  MOTOR 

1

25a MOTOR FAN 

1

25b MOTOR COVER 

1

25c CAPICITOR 

1

25d MOTOR ELECTRICAL BOX  1
25e TERMINAL WIRE CONNECTOR
25f START/STOP SWITCHES 

2

26  KEY 

1

27  MOTOR MOUNTING PLATE  1
28  BLOWER 

1

29  6” HOSE CLAMP 

2

30  6” HOSE 

1

31  IMPELLER 

1

32  FOAM GASKET 

1

33  24mm WASHER 

1

34  24mm LOCK WASHER 

1

35  M24 NUT 

1

36  6mm WASHER 

12

37  6mm LOCK WASHER 

12

38  M6X20 HEX SCREW 

12

39  CYCLONE BODY 

1

40  FOAM GASKET 

1

41  6” BAND CLAMP 

1

42  664 “T” LATERAL 

1

43  35 GAL. FIBER DRUM 

1

44  CYCLONE CONE 

1

44A 7” FLANGE 

1

45  7” HOSE CLAMP 

2

46  7” HOSE 

1

48  POWER CORD 

1

49  4” HOSE 

1

50  6” BELL CONNECTOR 

1

51  FILTER CANISTER 

1

52  FUNNEL REDUCER 

1

53  4” BLAST GATE 

1

54  4” HOSE CLAMP 

3

55  TEMPEST LABELS 

2

Stand Components

Cyclone Components

Phillips
Head Screw

Carriage
Bolt

Flange
Bolt

Flat Washer

Lock Washer

Hex Nut

Содержание TEMPEST TEMP2PCX













Отзывы: