background image

 

NOTE:

 

    It is recommended to install an outside air inlet of minimum 4” diameter in the room where the heating appliance is 
installed (see drawing below).  To do so, it is preferable to choose a wall which is not exposed to extreme winds, 
according to the conditions surrounding your house. 
 

 

 

 

N.B.  The owner of the furnace is responsible for the room salubrity in case of negative pressure or temporary 

negative pressure. 

 

ELECTRICAL CONNECTION 

  
    The following instructions do not supersede the local code. 
 
 

WOOD ONLY 

 
    Install the fan limit control on the support provided after securing this support on the left edge of the hot air plenum 
where two holes are pre-drilled (

there are four pre-drilled holes on the edge of the PSG3000, use the two that are 

located farther

 

back

).  Install the servo-motor on the facade above the door, on the right side (use pre-drilled holes).  

The chain that links the air inlet latch to the motor must have a play of 1/8 in.  When there is no call for heat, the air 
inlet latch must be completely shut and the chain must be affixed to the servo-motor at “8 o’clock”. 

*

 

        
 The red switch located on the junction box controls low speed operation of the blower, in either ON (continuous 
operation) or OFF modes. 
 

WARNING:  USE FEEDING WIRES SUITABLE FOR 75

O

 
WOOD/ELECTRIC 

 
    The high limit control on the electric unit is a manual reset thermostatic captor that is located directly inside the 
electric unit 

(see INSIDE VIEW OF THE ELECTRIC ELEMENT

).  The electric elements must be installed as shown on 

the diagram.  Install the wood combined fan limit control on the support provided, at the determined location. The 
connections must conform to the diagram. 
 
    Install the servo-motor on the facade above the door, on the right side (use pre-drilled holes).  The chain that links 
the air inlet latch to the motor must have a play of 1/8 in.  When there is no call for heat, the air inlet latch must be 
completely shut and the chain must be affixed to the servo-motor at “8 o’clock”.  

 
WARNING:  USE FEEDING WIRES SUITABLE FOR 75

O

 
    

(With all reserves on the minimum combustion air to be increased depending on the type and quality of the 

combustible). 

Insulated conduit full lenght 

Fresh air 

intake 

Exterior 

wall 

Free air 

entry 

Содержание PSG-2000









































Отзывы: