PRULITE.COM 213.746.0360
Prudential Ltg. reserves the right to change design specifications or materials without notice. Please visit prulite.com for most current data.
© 2015 All rights reserved – All products manufactured at: Prudential Ltg. 1774 E. 21st Street, Los Angeles, CA 90058
WARNING:
Ground fixture in accordance with local and national electrical codes. Failure to do so may result in serious personal injury.
6
3 of
LED
Bionic
| Recessed Linear
4˝ Slot
I N S T A L L A T I O N I N S T R U C T I O N S
CO N T IN U O U S R U N X 3, X 7
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
“L” Trim
8)
9)
Uninstall reflector
where wiring fixture
through top knockouts.
Make electrical
connections and
reinstall reflector.
Safety Cable
Reflector
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
“L” Trim
10)
Install trim and secure
to housing only.
X7 — PROCEED TO STEP 11
X3 — SKIP TO STEP 15
Trim
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
“L” Trim
13)
Remove shipping straps /
aperture guides.
MUST TEST lens fits in ALL (X7)
applications before mud-in.
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
“L” Trim
12)
Install screws through
backer flange (Recess.)
Secure trim to drywall using
drywall screws (by others).
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
TRIM WALL — X3
TRIM WALL — X7
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
NOTE: Leave 1/16˝ air
gap at each end of run.
Table saw or chop saw with
a 80T blade recommended.
16)
15)
Install lensing, cut
last piece to fit.
Install “U” end trims and
straight trims, cut last
piece to fit.
Tape and mud-in to trim (X7).
SHIPPING STRAPS
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
“L” Trim
11)
Re-install shipping
straps / aperture
guides. (X7 only).
SHIPPING STRAPS
C8 CORNERS:
Aligner
Spline
Blocking
(BY OTHERS)
2 x 6 Stud
Required
(BY OTHERS)
51/8” *
Finshed Wall Opening
5 Housing˝
53/4˝ *
Stud Aperture
* Keep finished wall opening and studs aperture as specified in the wall cross section.
LENS
WALL RAIL
LENS REMOVAL TOOL
8-32_X_3_8_HWH_SELF_TAP
ADJUSTABLE HANGER BRACKETS
T-BAR BRACKETS
OVERHEAD MOUNTING BRACKET
ALIGNER SPLINES
“L” Trim
14 a)
14 b)
SHIPPING STRAPS
Tape and
mud-in to
trim edge
(X7)
Remove shipping
straps / aperture
guides.
07-02-2020
