To do this, clamp it to the work piece using,
for example, C-clamps. In this way, the con-
tours of the template can be „traced“ with
the MOF foot-edge and the desired milled
groove can be made.
However, just as described in the previous
point, in this procedure it is better to take
the clearance between the outer edge of the
MOF device foot and the mill cutter router
bit into consideration, which should also be
done when cutting the template.
7.6 „On-the-fly“ submersion (fig. 11)
This refers to a method in which one does
not press the milling cutter onto a work
piece edge in the work piece, but starts the
groove in the work piece surface freely.
Caution: Please note, so-called on-the-fly
submersion is not to be used for all types of
milling! Naturally, it must have corresponding
cuts on the bottom side also.
1. Pre-select the milling depth. To do so,
please start out as previously described
in the chapter „Milling depth adjustment“,
but only up to and including point 6: the
setscrew should be at the desired posi-
tion, but the locking lever (fig. 11, pos. 2)
remains open.
2. Place the mill at the desired position on
the work piece and switch it on.
3. Slowly press the milling cutter down until
setscrew 1 is seated on the column for
depth-control stop 3. The mill thereby
submerses into the work piece.
4. Mill out the desired groove.
5. If necessary, you can fix the milling height
with locking lever 2.
8 Service and maintenance
8.1 General
DANGER!
Always turn switch OFF and always remove
plug from power source before making any
adjustments, repairs, changing accessories,
or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
DANGER!
Any attempt to repair or replace electrical
parts on this tool may create a hazard un-
less repair is done by a qualified service
technician.
Electrical or mechanical repairs should be
done only by qualified service technicians.
When servicing use only PROXXON replace-
ment parts. Use of any other parts may cre-
ate a hazard or cause product damage.
Repair service is available at your PROXXON
service center (You will find the address at
the back of this manual).
WARNING!
To avoid fire or toxic reaction, never use
gasoline, naphtha, acetone, lacquer thinner,
or similar highly volatile solvents to clean the
power tool.
Do not allow brake fluids, gasoline, or pene-
trating oils to come in contact with the plas-
tic parts. They contain chemicals that can
damage or destroy plastics! Do not use sol-
vents or cleansing agents containing alcohol
(e.g. benzene, cleaning alcohol, etc.) as
these can corrode the plastic housings.
The MOF surface mill is extensively mainte-
nance free. However, to ensure a long serv-
ice life you should clean the device after
each use with a soft cloth, swab, or brush. A
vacuum cleaner is also advisable for this.
External cleaning of the housing can be car-
ried out using a soft, possibly moist cloth.
While doing so, a mild detergent or other
suitable cleansing agent can be used. Do
not use solvents or cleansing agents con-
taining alcohol (e.g. benzene, cleaning alco-
hol, etc.) as these can corrode the plastic
housings.
8.2 Adjusting the clamping (Fig. 13):
If the clamping effect is not sufficient for
working, the clamping force of the stop lever
of the height adjustment can be reset. Un-
screw the grub screw 1 and turn the slotted
screw 2 slightly clockwise. Then check the
clamping effect by activating the stop lever 3.
Once the desired effect has been achieved,
tighten the grub screw 1 again.
15
Содержание MICRO-Router MOF
