---------- PROXEL ENGINEERING ---------------- www.proxel-bg.com-------------------------------- 3WMREG rev. 2.4 /02.2017------
PulseDur
[3.5sec]6
Ext T L
[-25ºC]11
[10sec] 8
ON<>OFF
[ 60sec]7
Period-
[10sec] 9
Passwrd
[00] 10
Ext T M
[ 0 ºC]12
Ext T H
[ 25ºC]13
Window/Screen #6 –Duration of output pulse for fine adjustment
Row 1
: Displays the selected parameter “PulseDur”
Row 2
: The value of the parameter. Range 0.5 ÷ 5.0sek.
Screen [6] .
* to change this parameter a password is required
Window/Screen #7 - Total Time to fully open / close the actuator.
Row 1
: Displays the selected parameter “ON<>OFF”
Row 2
: The value of the parameter. Range 15÷250sec.
Screen [7]
.
* to change this parameter a password is required
16.
Window/Screen #8 -
Period of applying signal pulse for direction “open”
Row 1
: Displays the selected parameter “”
Ред 2
: The value of the parameter. Range 10 ÷ 60sec.
Screen [8]
.
* to change this parameter a password is required
17.
Window/Screen #9 -
Period of applying signal pulse for direction “close”
Row 1
: Displays the selected parameter “Period-”
Row 2
: The value of the parameter. Range 10 ÷ 60sec.
Screen [9] .
* to change this parameter a password is required
Window/Screen #10 - Password field to access protected parameters.
Row 1
: Displays the selected parameter “Passwrd”.
Screen [10]
Row 2
: Set password.
Enter the required password to access the protected parameters.
Window/Screen #11
-
Lower point of ambient temperature to describe the temperature
curve (corresponds to "FluidHi")
Row 1
: Displays the selected parameter “Ext T L”
Row 2
: The value of the parameter. Range -35ºC ÷ “Ext T M-1” ºC.
Screen [11]
* to change this parameter a password is required
** the parameter is only visible only if operation mode is ambient temperature correction
Window/Screen #12 - Middle point of ambient temperature to describe the temperature
curve (corresponds to average of "FluidLo and FluidHi")
Row 1
: Displays the selected parameter “Ext T M”
Row 2
: The value of the parameter. Range “Ext T L+1” ºC ÷ “Ext T H-1” ºC.
Screen
[12] .
* to change this parameter a password is required
** the parameter is only visible only if operation mode is ambient temperature correction
Window/Screen #13 – Middle point of ambient temperature to describe the temperature
curve (corresponds to of
“
FluidLo”)
Row 1
: Displays the selected parameter “Ext T H”
Row 2
: The value of the parameter. Range “Ext T M-1” ºC ÷ 60 ºC.
Screen [13]
* to change this parameter a password is required
** the parameter is only visible only if operation mode is ambient temperature correction
---------- PROXEL ENGINEERING ---------------- www.proxel-bg.com-------------------------------- 3WMREG rev. 2.4 /02.2017------
[Setp
ºC
]
:ExtTemp
02f90278
03ff
FluidLo
[ 40ºC]14
FluidHi
[ 85ºC]15
CorrFlu
[ 0ºC]16
[Setp
ºC
]
:Local T
Window/Screen #14 – Minimum temperature of the fluid to describe the temperature curve.
(corresponds to "ExtT H")
Row 1
: Displays the selected parameter “Fluid Lo”
Row 2
: The value of the parameter. Range -10ºC÷“Fluid Lo”+3 ºC.
Screen [14]
* to change this parameter a password is required
** the parameter is only visible only if operation mode is ambient temperature correction
Window/Screen #15 – Maximum temperature of the fluid to describe the temperature curve.
(corresponds to "Ext T L")
Row 1
: Displays the selected parameter “Fluid Ho”
Row 2
: The value of the parameter. Range “Fluid Lo”+3÷90ºC.
Screen [15]
* to change this parameter a password is required
** the parameter is only visible only if operation mode is ambient temperature correction
Window/Screen #16 – Temperature correction FluidLo and FluidHi "total. (fast and
simultaneous increase / decrease together of temperatures
Row 1
: Displays the selected parameter "CorrFlu"
Row 2
: The value of the parameter. Range -5ºC ÷ + 5ºC.
Screen [16]
* to change this parameter a password is required
** the parameter is only visible only if operation mode is ambient temperature correction
Window/Screen #17 - Selection of the working circuit (with or without compensation for
ambient temperature).
Set the operational mode
Row 1
: Displays the selected parameter “Setp
°
C”.
Row 2
: The selected scheme of work –Sch.1=“:ExtTemp”, Sch.2=”:Local T”,
Attention! For the correct operation of the device, observe the correct setting of the
controller operating diagram
* to change this parameter a password is required
Window/Screen #18 - Calibration of temperature inputs (service mode).
Temperature curve
