ProX BlitzzFX Operators Manual
Page 2
Version: 1.5 (12/15/2022 1:22 PM
1. When the power is disconnected, place the UNITS horizontally, and inspect them for damage on all sides before
eachuse. If damaged, do not operate and immediately contact ProX for service.
2. Unscrew the lid of the powder tank to pour in the ProX BlitzzFX Powder, and then lightly tighten the lid. (Use
ONLYProX branded powder)
3. Before power on, please verify that the supply voltage is in conformity with the rated voltage of the machine.
Atpower on, the indicator light will turn on, and the machine will begin to heat for use. Connect the machine to
yourpreferred controller.
Allow up to 30 Minutes for the machine to warm before each use.
Once heated for use,
it will remain ready as long as power is connected.
4. The machine must be used only in a well-ventilated place. Although this is a COLD effect, it may create a very
smallamount of smoke/haze during operation.
5. Outdoor powder CANNOT be used indoors due to the 16’ fountain capability! When using outdoor powder
thereshould be no flammable materials in a 16 ft. radius above, around and under the Blitzz machine.
6. Spark powder should not be exposed to the air. Once a bag of powder is opened it should be used up or placed
inan airtight sealed container. Never expose spark powder to open flames. Do not discard in fire. After each use
besure to empty unused granules from the bin and run a cleaning cycle. Power Clean AFTER WARMUP! (Push
andhold W3 Remote Button #2 for more than 10 seconds to start clean cycle, it will run 15 seconds or Press #2
againto stop. This ONLY removes granules in the spark tube, not storage tank! Be sure to put the unused
granules inairtight storage such as a quality zip-lock bag. Granules left in the machine, or exposed to the air
will tend tooxidize and clump into hard deposits. If left in the machine, they can/may clog the machine and
damage thespark chamber. This is not covered by the warranty.
7. Do not touch the device during operation as the housing will be hot to touch. Provide a minimum of a 3-foot
safezone with nothing but the power and signal cables for the Blitzz units in that area. Provide a 10-foot
separationbetween the machines and the audience and any other obstruction! Multiple machines may be placed
on 4’ centers while maintaining the 10’ area between any machine and the spectators audiece/walls/stages/etc.
8. Keep this device in a dry area at all times. Do not allow water to enter the unit at any time.
9. The BlitzzFX machines MUST be in the vertical position at all times when there is powder in the tank. Removeall
powder prior to transport or risk creating a blockage in the mechanical system.
10. Disconnect all power servicing the unit. No operator serviceable parts inside. Return to ProX for repairs
orrefurbishing.
11. Damage caused from not following the guidelines in this manual are not covered by the warranty and ProX will
notaccept responsibility for any resulting defects or problems.
12. A qualified technician should install and service this device.
13. Do not switch the device on immediately after it has been exposed to extreme changes in temperature
especiallyvery cold conditions. Protect the device against damage by leaving it switched off until it has
reached roomtemperature.
14. This device falls under NEC Class 1. It is essential that the device be earth grounded. Do not remove or isolate
thegrounding pin.
15. Make sure that the available voltage does not exceed the voltage stated in the specification section of this manual.
16. Do not crimp the power cord. Protect it against damage. Have an authorized service center replace it if necessary.
17. Disconnect the device from all power to clean it or when it is not in use. Handle the power cord by the plug
endsonly.
18. Note that ANY modification to the device is not covered by the product warranty and will VOID the warranty.
19. Keep the device away from children and untrained/unauthorized users.
AD)
a. Do not allow machine to run out of powder. If the machine is allowed to run empty, it may cause the
mechanical system to be damaged.
b. IMPORTANT: Turn off the power before adding effect powder.
IMPORTANT:
never pour spark powder into the spark discharge opening, This can be dangerous.
Spark powder must only be added to the storage tank that requires the removal of the protective cap.
DO NOT OVERFILL – AFTER FILLING REPLACE CAP AND TIGHTEN.
