manualshive.com logo in svg

Protrol IPS2 24 VDC, Руководство пользователя, Страница: 4 / 25

Поделиться
Скачать
Protrol IPS2 24 VDC Скачать руководство пользователя страница 4

 

Ver 1710 Rev 1

 

Protrol AB

 

 

Tel: 031- 45 82 00

 

Ullevigatan 19 

 

internet: www.protrol.se  

411 40 Göteborg 

4

 

e-mail: [email protected]

 

3  Safety Information 

 

 

The device should be connected to a ground terminal. 

 

If the cover is removed, avoid contact with the main circuit board and terminals. The unit is 

powered by 24 VDC but the wires to binary inputs and outputs are designed for higher signal 
voltages. 

 

If the unit is disconnected and the cover is removed, make sure that proper precautions are made 

to protect the unit from electrostatic discharges.  

 

When connecting and disconnecting the current terminals always short-circuit the current path to 

avoid open circuits!   

 

Short circuiting the current terminals when the earth fault detector is enabled is likely to be 

interpreted as an apparent earth fault. If the EF detector has no binary input qualification enabled 
the IPS2 unit should either be switched off or pluggable connectors in X2-X3 should be 
disconnected.  
 

Hint: T

his “feature” can be used for example in a test situation when the whole chain from 

IPS2 to 

the SCADA system should be verified. When the IPS2 unit is in operation and there is a normal load 
current it is usually possible to activate the earth fault detector by short-circuiting one phase on the 
terminal screws with a short cable. 

Содержание IPS2 24 VDC


























Отзывы:

Нет отзывов