manualshive.com logo in svg

Protrol IPS2 24 VDC, Руководство пользователя, Страница: 22 / 25

Поделиться
Скачать
Protrol IPS2 24 VDC Скачать руководство пользователя страница 22

 

Ver 1710 Rev 1

 

Protrol AB

 

 

Tel: 031- 45 82 00

 

Ullevigatan 19 

 

internet: www.protrol.se  

411 40 Göteborg 

22

 

e-mail: [email protected]

 

Connect the adapter to the maintenance PC using an USB cable.  

The needed extra files for the adapter are included in the Protrol IPS2 24 VDC Configuration Tool 
installation package

, version 2.0.0 and higher. Make sure that you have the files “SiUtil.dll” and 

“USBHIB.dll” in the same folder as the configuration tool.

 

Downloading configuration file 

Follow the steps below to download the configuration file. 

1.

 

Connect the IPS2 device as described above. 

2.

 

Power-up the IPS2. 

3.

 

Start the Protrol IPS2 24 VDC Configuration Tool (if not already started).  

a.

 

Make sure you have version 2.0.0 or later of the tool. 

b.

 

Check also that you have the files “SiUtil.dll” and “USBHIB.dll” in the same folder as the 

configuration tool. 

4.

 

Open the configuration file to download (the 

Open

… button) 

 

or make sure you save the settings you currently made (press the 

S

ave As…

 button). 

a.

 

Please observe that the download function only uses the file name in the field and 
download that file to the IPS unit. It will not check for any differences or unsaved settings in 
other settings fields.  

5.

 

Press the 

Download

 button. 

 

6.

 

Press 

OK

. 

a.

 

A confirmation dialog will be displayed with information.  

7.

 

Done! 

 

Содержание IPS2 24 VDC


























Отзывы:

Нет отзывов