Protrol IPC4020 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 63

background image

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

9

e-mail: [email protected]

4.3 Internal Supervision

Internal check of CPU-near hardware and software modules is performed at startup.

▪

Memory check

–

activates IRF

▪

Flash memory check

–

activates IRF

▪

Expansion board check

–

activates IRF

▪

Execution of software modules

–

activates IRF

▪

Supervision of external interfaces

–

rapported in Event Log

Supervision of expansion boards and execution of software modules are performed continuously.

4.4 Interfaces

4.4.1 RS485/RS422 port for IEC 60870-5-101 Slave and PDCIO

IPC402x has a signal interface on the left of the front panel for connection to the remote control center
using the communication protocol IEC 60870-5-101.

This port supports 2-wire (half duplex) communication. It is factory set to 8-E-1, i.e., 8 data bits, even parity
and 1 stop bit. With options where the front panel is modified, it is possible to handle both 4-wire (full
duplex) or RS232 communication.

There is built-in protection for surge voltages. However, cables for communication that may be subjected
to overvoltage must have a primary protection, for example Protrol OVP. As a rule of thumb, one can say
that cables that leave the building / station must be supplemented with a primary protection.

Terminals

Terminal/pin

Short name

Description

X11:1

TX+

Sender (plus)

X11:2

TX-

Sender (minus)

X11:3

RX(TX)+

Receiver (plus), (also sender when 2-wire)

X11:4

RX(TX)-

Receiver (minus), (also sender when 2-wire)

X11:5

TERM

Termination for receiver. Connect to X11:4 for activation

Terminering

The first (master) and last device (last slave) on the communication line should be terminated. This is
done on IPC402x by short-circuiting X11:4 and X11:5.

The terminals X11:3 and X11:4 are used for 2-wire communication. Configuration according to Chapter 7.2.

The terminal X11 is also used as the physical interface when the expansion device PDCIO is used. PDCIO is
connected to the terminals X11:3 and X11:4 in the same manner as when 2-wire-communication is
employed for communication with the remote control centre using IEC 60870-5-101.

Observe that PDCIO can only be used if IEC 60870-5-104 is used for communication with the remote control
centre.

«
...
7
8
9
10
11
...
»

Содержание IPC4020
































































Отзывы:

Нет отзывов

Похожие инструкции для IPC4020

Бренд: 3M Страницы: 8

LevelPro ProScan 3 Series

Бренд: ICON Страницы: 14

Level pro 200C Series

Бренд: ICON Страницы: 19

Бренд: M-system Страницы: 3

Бренд: Agile Remote Cameras Страницы: 4

Бренд: GST Страницы: 11

Бренд: GCE Страницы: 28

Бренд: jablotron Страницы: 2

Бренд: Interlogix Страницы: 8

Бренд: Wisenet Страницы: 65

Бренд: KAYS TECH Страницы: 11

Бренд: DSE Страницы: 2

Бренд: IVIEW Страницы: 29

Бренд: SHIRE CONTROLS Страницы: 10

Бренд: Ziton Страницы: 13

Бренд: Bosean Electronic Technology Страницы: 16

Бренд: D-MAX Страницы: 28

Бренд: jablotron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды