Protrol IPC4020 Скачать руководство пользователя страница 22

Страница: 22 / 63

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

e-mail: [email protected]

7.2 General Settings

– Communication

This section describes the configuration settings for remote communication; IP addresses, and general
settings for IEC 60870-5-101 and IEC 60870-5-104.

7.2.1 Communication

– Ethernet

The settings for

Ethernet

are found on the

Config/Communication/Ethernet

tab

Settings -

Ethernet

Parameter

Description

Range

Factory value

Unit

Settings for unit:

Enable static IP

Fixed or dynamic IP address (via DHCP).

Yes or No

Yes

IP address

Fixed IP address for the device.

192.168.0.31

Netmask

Netmask

255.255.255.0

Gateway

IP address for network gateway

192.168.0.1

Trusted IP addresses for IEC 60870-5-104:

IP address n

Address

of IEC 60870-5-104 master (

= 1, 2, … )

192.168.0.10n

Enable n

Accept connection from this address.

If no address is specified, connection is accepted
from all addresses (within the Netmask).

Yes or No

7.2.2 Communication

– IEC 60870-5-101/104

There are three sub-tabs on the

IEC 60870-5-101/104

tab, or four if the option

”

101 Master”

is enabled.

Each tab and its settings are described in the following chapter.

Range according to common notation (4 bytes in decimal form, 0..255). Observe that the address 0.0.0.0 is not

allowed.

Содержание IPC4020
































































Результаты поиска

Содержание IPC4020

Отзывы:

Похожие инструкции для IPC4020

Бренды по названию

Популярные бренды

Protrol IPC4020, Руководство пользователя

Результаты поиска

Содержание IPC4020

Отзывы:

Похожие инструкции для IPC4020

Бренды по названию

Популярные бренды