DIGITAL WRIST BLOOD PRESSURE MONITOR - PH 168KD
This material had been developed in interest of customer training program
by PROTON Healthcare Ltd. and downloaded from www.protonhealthcare.com
F. Storing, recalling and erasing measurement data:
a. Storing data:
After each measurement, the systolic rate, diastolic rate,
heart pulse rate, time and date will be automatically
stored. The memory holds 3 memory zones. Each
memory zoen stores the latest 40 measurement data. If
more than 40 measurements are entered, the memory
will automatically clear out the earliest data.
b. Recalling data:
1 Press the “MEMORY” button to enter Memory Recall
Mode.
2 Press button to select the memory zone (1, 2
or 3).
3 If there’s no data in the memory, nothing will appear on
screen.
4 If there’s data in the memory, the first reading will be
the average of the latest 3 measurements (Systolic,
Diastolic and Pulse rate) in the selected zone.
5 Press “MEMORY” or button again, the latest
measurement will appear along with the memory
number, recording date and time.
6 Press “MEMORY” or button to review and scroll
through the stored data from the latest measurement
to the earliest one.
7 To stop reading memory, press “START/STOP” button
(system switches to standby mode).
*Note!
The irregular heart beat detected record won’t be stored in
memory.
c. Erasing data:
1 Press “MEMOERY” button to enter Memory Recall
Mode.
2 Press button to select the memory zone (1, 2
or 3).
3 Press “MODE” and buttons simultaneously, all stored
data in the selected memory zone will be erased.
4 To check if the data is erased, press “MEMOERY”
button and no data should appear on the screen.
G. To change batteries:
When the symbol appears on the display, the
battery is weak. Change the batteries or it will not be
able to take measurement.
Take out used batteries and put in 2 pcs of new alkaline
batteries.
*Attention!
• All batteries used must be the same type. Do not mix
alkaline, standard (carbon-zinc) or rechargeable (cadmium)
batteries.
• Do not mix old and new batteries.
• When changing the batteries, all stored data will not
disappear.
10. Maintenance
•
Clean the device body, case and the cuff carefully with
a clean, soft and slightly dampened cloth and then wipe
them dry with another piece of dry cloth.
•
Do not use thinner, alcohol, petrol (gasoline) or any
strong cleansers to clean.
•
Do not wash the cuff or make it wet, and never use
chemical cleaner on it.
•
Make sure no water will enter the main unit.
•
When the unit is not to be used for a long time, remove
the batteries. (Leaking of battery liquid can cause
damage.)
3
c. Press button to select the memory zone
(1, 2 or 3).
*Note!
• When taking repeated measurements, make sure to
select the same memory zone number before pressing
“START/STOP” button, so the measurement is registered
to the appropriate memory.
• Do not move or talk during measurement.
d. Press “START/STOP” button to start measurement. The
monitor will automatically inflate to the level that is right
for you.
e. After the air pressure is increased, it will slowly be
decreased. When the pulse rate is detected, PULSE
symbol will start flashing.
f. After taking blood pressure measurement, the systolic
rate, diastolic rate and heart pulse rate will be on the
display for 1 minute.
g. If the Systolic or Diastolic rate of
the result is greater than your preset
personalized level, the digit of
Systolic or Diastolic rate will flash.
If the Systolic or Diastolic rate of
the result is equal to or less than
your pre-set personalized level, the
SMILE FACE symbol will flash.
h. The device will automatically shout off if without any
operation after 1 minute.
*Note!
To stop reading or exit setting mode in process, press
“START/STOP“ button, system will go back to standby
mode. Press and hold “MODE” button, you may check the
pre-set personalized levels.
Move wrist upward
Move wrist downward
Move wrist to left
Move wrist to right
*Note!
• The Wrist Position Indicator function is optional. If it is
switched off, the device won’t show the symbols to indicate
the optimal position of the wrist while measuring.
• User can press “START/STOP” button to exit setting
mode and go back to standby mode at any step.
d. Wrist Position Indicator function in measurement:
(1) While measuring, slowly move your wrist according to
the Arrow symbols on screen to adjust the wrist angle.
(2) when the wrist is in the right position, all Arrow symbols
will disappera and PULSE symbol will flash twice on
screen. Then the measurement will automatically begin.
E. Steps to take blood pressure measurement:
a. Wrap the cuff around the arm (Refer to Wrapping of
Wrist cuff as Figure No.5)
b. Sit upright on the chair to have correct posture. (Refer to
Correct Posture in Taking Blood Pressure as Figure No.6)
