background image

WARNING: 

These instructions must be provided to the user and installer of this equipment. The user and installer of 

this equipment must read and understand these instructions before use or installation. Follow the manufacturer’s 

instructions for other safety equipment used with this system. Follow these instructions for proper use, 

inspection, and maintenance of this equipment. This product is intended to be used as a part of a complete Cabloc 

ladder safety system. Alterations, substitutions, or misuse of this equipment, or failure to follow instructions, 

may result in serious injury or death.

IMPORTANT:

 If you have questions on the installation, use, maintenance, or suitability of this equipment for 

your application, contact PROTECTA.

IMPORTANT:

 Before using this equipment, record the product identi

fi

 cation information from the installation and 

service label in the “Inspection and Maintenance Log” at the back of this manual.

Figure 1 - Cabloc Detachable Cable Sleeves

7 x 19 Constructed 

Steel Cable 

(Carrier Cable)

Cable 

Installation 

Slot

Cable Shoe

Attachment 

Point

Brake Lever

Carabiner

Sleeve 

Body

Model

Cable Dia. Safety Standard

Anti-Inversion

AC350A

5/16” 

(8 mm)

ANSI A14.3

AC351A

3/8 “ 

(9.5 mm)

ANSI A14.3

AC350C

5/16” 

(8 mm)

CSA Z259.2.1

AC351C

3/8 “ 

(9.5 mm)

CSA Z259.2.1

7 X 19 CABLE ONLY:

 Cabloc Cable Sleeves shall only 

be used on 7 x 19 constructed cable of the diameters 

speci

fi

 ed above.

1.0 APPLICATIONS

1.1 PURPOSE: 

The Cabloc detachable cable sleeve is designed to arrest the fall of personnel while climbing a 

fi

 xed ladder. The detachable cable sleeve is not intended to be used for material handling.

NOTE: 

The installer and user must ensure the ladder meets all applicable local, state, and federal 

standards, including ANSI A14.3.

1.2 LIMITATIONS:

 Cabloc detachable cable sleeves must be used with a PROTECTA approved ladder safety 

system. Use only the Cabloc Sleeve model speci

fi

 ed in Figure 1 for you applicable cable diameter and safety 

standard(s). The Cabloc cable sleeve must be directly connected to an approved full body harness with the 

carabiner supplied with the sleeve (see Figure 1). Do not use connection devices other than the supplied 

carabiner. Do not add additional connectors or lanyards between the user and the cable sleeve.

NOTE: 

ANSI A14.3 and OSHA 1926.1053 states that the length of connection between the carrier cable 

and attachment point on the full body harness must not exceed 9 in. (0.2 m) in Canada per  CSA Z 259.2.1-98.

1.3  

Refer to applicable local, state, and federal (OSHA) requirements governing this equipment for more 
information on ladder safety systems and associated components, including OSHA 1910.27.

User Instruction Manual Cabloc

 

Detachable Cable Sleeve

This manual is intended to be used as part of an employee training program as recommended by OSHA.

Instructions for the following series products:

LADDER CLIMBING CABLE SLEEVE

 

Model Numbers: See Figure 1

© Copyright 2012, Capital Safety

Form No: 5902216  Rev: F

Содержание AC350A









Отзывы: