WARNING :
Before proceeding with the control board commissioning, check which kind of limit
switch is installed on the motor.
The control board is preset to work with electromechanical limit switches
.
In case of magnetic limit switch please select parameter:
Method
1
=
STANDARD
Method
2
=
SEQUENTIAL
Warning:
Before powering up and programming the control unit refer to the wiring scheme and then:
1
Check that the motor connections are correct
2
Check that the photocell connections are correct
Important:
If the photocells are not installed in closing phase, you must link terminals 3 and 9.
If the photocells are not installed in opening phase, you must link terminals 4 and 9.
3
Check that the control connections are correct.
Important:
If an emergency stop button is not fitted, you must link terminals 2 and 8.
4
Use the motor release key supplied to disengage the electric motor from the
mechanical drive; then close the gate and re-engage.
5
Power the control unit up
STANDARD PROGRAMMING PROCESS
(
Method 1)
a
) Give a
START
signal (terminal 1 and terminal 8).
After an opening movement of about 240mm, the deceleration phase will start (since
the control board is pre-adjusted for an opening of 2,50 m). T
he motor will wait about 3 seconds and after that will start again with the closing phase.
b
) Give a
START
signal to verify which functions and times are not suitable with the
installation and take note.
c
) Enter the programming phase through the
buttons A
and
B
to reach the wished
parameter
d
) Use the buttons
C
and
D
to change or confirm every single parameter
e
)
IMPORTANT:
save the changes by selecting the parameter and pushing the
button C
.
Example:
Increase the motor working time by 5 seconds
With the switched on control board , ensure that the display shows :
Press
button
A
until the display shows
Press
button
B
until the display shows
Wait
until the display shows
Press 5 times the
C
until the display shows
Press
button B
ntil the display shows
u
Press the button C for some seconds
ntil the display shows
u
The motor working time has been increased from 21 to 26 seconds
SEQUENTIAL PROGRAMMING
(
method 2)
SLIDING GATE SEQUENTIAL PROGRAMMING
a
) Press
button A
(steps through the top menu) until the display shows
b
) Press
button B
(steps through the sub-menu) until the display shows
c
) Give a
START
signal: the leaf starts opening and the display shows
d
) Wait until the leaf has done the 90% of the opening cycle and then give
another
START
signal: the display shows and the deceleration phase
begins.
e
) When the opening phase has been completed (
OPENING LIMIT
SWITCH
) and the display shows , the control board has stored the
opening and deceleration times and starts calculating the “
stay open
”
(pause) time
f
)
At the reaching of the desired pause time, give another
START
impulse.
The control board has stored the “
stay open
” time and the gate starts the
closing cycle.
g
) When the closing cycle has completely finished, till the complete closure
of the gate, the control unit automatically exits from the sequential
programming process and all the working times have been saved.
PROGRAMMING THE Q60S W PARAMETERS
SELF-DIAGNOSIS DISPLAY MESSAGES
U
S
I
I
I
P
AS
P E
C
F
Closing phase photocell
beam interruoted
or wiring fault
Pedestrian start signal
(short circuit between
terminal7 & 8)
Limit switch
in opening phase
Motor problem (wiring
fault, obstruction or
torque setting too low)
Limit switch
in closing phase
F A
5
C
A
.
P A
I
I
S U
2 5
— —
— —
Photocell’s test error
E
Both opening and closing
phase photocell beam
interrupted or wiring fault
Start signal
(short circuit between
terminal 1 & 8)
Stop pressed
(or open circuit between
terminal 2 & 8)
Radio fob
continuously
trasmitting
SPECIAL FUNCTIONS
P A
E
P
2
P
AUTOMATIC CLOSING FUNCTION
When set to YES
(“SI”):
- an impulse during the opening phase will stop the
motors until another impulse is received
- an impulse during the closing phase will stop and
reverse the motors
When set to NO
, the step-by-step operation is active:
st
- 1 impulse starts the
opening phase
nd
- 2 impulse stops the
opening phase
rd
- 3 impulse starts the
closing phase
MULTI-USER FUNCTION
when set to
YES
(“SI”):
The control unit will not accept any
command during the opening phase
PROGRAMMING THE RADIO
LLLLL
IMPORTANT
:
BEFORE PROGRAMMING FOR THE FIRST
TIME THE RADIO RECEIVER, DELETE ALL THE RECORDED TEST CODES.
SEE FUNCTION AT THE BOTTOM OF THIS CHAPTER
IN CASE OF TRANSMITTERS WITH DIP-SWITCHES, SET THE
MICROSWITCHES TO CREATE A NEW PERSONAL CODE.
(For security reasons avoid to set the microswitches all in OFF or all in ON position).
IN CASE OF HIT TYPE TRANSMITTERS, THE ABOVE MENTIONED
PROCEDURE IS NOT NECESSARY BECAUSE EACH TRANSMITTER
COMES WITH ITS OWN CODE RANDOM.
DISPLAYING STORED CODES
Press the
button A
repeatedly until the display shows
Press
button B
until the display shows
The display will now cycle trough each stored code from 01 to 50.
TO ERASE A SINGLE STORES CODE
Press
button D
when the number of the code to be removed is displayed
STORING NEW REMOTE CONTROL CODE
-
Press the
button A
repeatedly until the display shows
-
Press
button B
until the display shows
-
Press and hold the remote control button until a dot appears on the display (this
means that the receiver is ready to store a new code) and simultaneously
press
button C
to store the new code
STORING NEW REMOTE CONTROL CODE with STOP function
-
Press the
button A
repeatedly until the display shows
-
Press
button B
until the display shows
-
Press and hold the remote control button until the dot appears on the display
and simultaneously press
button C
to store the new code.
STORING NEW REMOTE CONTROL CODE with PEDESTRIAN function
-
Press the
button A
repeatedly until the display shows
-
Press
button B
until the display shows
-
Press and hold the remote control button until the dot appears on the display
and simultaneously press
button C
to store the new code
DELETING ALL STORED CODES
-
Press the
button A
repeatedly until the display shows
-
Press
button B
until the display shows
-
Press and hold
button D
until the display shows
This indicates that all the codes have been erased
A
A
A
A
A
P
C
P
C
P
P
P
P
C
C
C
A
NO
F
YES
F
PHOTOCELL OR SAFETY RUBBER EDGE
IN OPENING PHASE
Содержание Q60S
Страница 2: ......
