manualshive.com logo in svg

Protec WB-514, Руководство пользователя

Поделиться
Скачать
Protec WB-514 Скачать руководство пользователя страница 26

２１

 

8 Prompt Information 

Users can process prompt information according to the following instructions. 

It gives Information to prompt the current state of the system 
during measurement. 

 
It reminds that START key is pressed without closing the 
guard when the guard is set enabled   

 
Interrupt measurement in emergency!  System gives the 
prompt when the STOP key is interrupted accidentally 

 

When the guard is opened artificially during rotation 
measurement, the balancer stops suddenly and prompt is 
given. 
 
Prompt is given and measurement is stopped when rotating 
speed is too low to meet the basic measurement needs,   

The measurement rotation is in wrong direction. This usually 
will appear in the three-phase motor control balancer due to 
sequence errors 

It prompts gauge inner error. Check the error in system testing. 
The normal problem can be solved by automatic gauge 
self-calibration, otherwise, check the sensor of the gauge. 

This is an extension .No gauge B is equipped in this model. 
 
 
 
 
 

                                                          WB-514 Wheel Balancer user’s manual 

Содержание WB-514
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды