ProTeam AC10P Скачать руководство пользователя страница 34

34 

 

 

6.7 Failure code table for general PCB (single-system) 

 

Wire 

controller  

Protection

/

Failure  

Check  

Solution  

PP01/PP1  

Inlet water temp. sensor failure  

1. Check the connection of inlet water     
sensor.  
2. Check if the sensor is broken.  

1. Reconnect the sensor.  
2. Replace the sensor.  

PP02/PP2  

Outlet water temp. sensor failure  

1. Check the connection of outlet water    
sensor.  
2. Check if the sensor is broken.  

1. Reconnect the sensor.  
2. Replace the sensor.  

PP03/PP3  

Coil temp. sensor failure  

1. Check the connection of coil     
temperature sensor.  
2. Check if the sensor is broken.  

1. Reconnect the sensor.  
2. Replace the sensor.  

PP05/PP5  

Ambient temp. sensor failure  

1. Check the connection of ambient 
temperature sensor. 
2. Check if the sensor is broken.  

1. Reconnect the sensor.  
2. Replace the sensor.  

PP06/PP6  

Protection for excessive temp. 
difference between water inlet & 
outlet  

1. Check if there is any blockage in the 
water     circuit.  
2. Check if the water flow volume is 
enough. 3. Check if the water pump is 
working.  

1. Remove the cause of the 
blockage.  
2. Increase the water flow 
volume.  
3. Repair or replace the water 
pump.  

PP07/PP7  

Anti-freeze protection for 
cooling  

Refer to PP06.  

Refer to PP06.  

PP07/PP7  

Winter anti-freeze protection 

  

No action required  

 

PP07/PP7  

Winter anti-freeze protection 

  

No action required  

EE01/EE1  

High pressure protection  

1. Check if high pressure switch is 
broken  
2. Check if there's a blockage in the 
water circuit or if water flow is not 
enough.  
3. Check if refrigerant circuit jam.  

1. Replace with new high 
pressure switch.  
2. Fill up with enough 
refrigerant.  
3. Remove cause of blockage or 
increase water flow.  
4. Send heat pump to dealer for 
detailed check.  

EE06/EE6  

Low pressure protection  

1. Check if low pressure switch is 
broken.  
2. Check if refrigerant level is low.  
3. Ambient temp. and water inlet temp. 
is too low.  

1. Replace with new low 
pressure switch.  
2. Fill up with enough 
refrigerant.  
3. Send heat pump to dealer for     
detailed check.  

EE03/EE3  

Water flow switch failure  

1. Check if wiring connection of flow 
switch is in correct position.  
2. Check if there is enough water flow.  
3. Check if flow switch is broken.  
4. Check if water pump is working.  

1. Reconnect the wiring.  
2. Increase water flow.  
3. Replace flow switch.  
4. Repair or replace water pump.  

EE04/EE4  

Order of phases incorrect (only 
for 3 phase model)  

Order of phases incorrect  

Reconnect the phases in right 
order.  

EE05/EE5  

Failure of excessive temp. 
difference between water inlet & 
outlet  

1. Check if there is enough water flow 
volume.  
2. Check if inlet / outlet water temp. 
sensor is working.  

1. Increase water flow.  
2. Replace sensor.  

Содержание AC10P





































Отзывы: