background image

Page 14 of 14

09-13-568-Rev5

Caution

• 

The Mounting Brackets can carry up to 25 kg of equipment per pair. Ensure all items are securely attached.

• 

Ensure that all loads are distributed evenly across the roof racks and are fastened securely.

• 

A loaded roof rack system can alter the performance of your vehicle. Be especially aware of the effects of side winds, 
changing of direction, and braking performance. Avoid rapid acceleration and deceleration. Drive Carefully.

• 

Make sure all loads are securely fastened with non-elastic Straps. Check regularly during longer journeys.

• 

Never drive into a car wash with the roof rack system or accessories 

fi

 tted.

• 

Do not exceed the vehicle manufacturer’s roof load rating. Total load equals weight of roof racks + acces cargo/
equipment.

Prorack

17 Hinkler Court, Brendale
QLD 4500, Australia

Freephone                                 www.prorack.co.za
AU: 1800 143 548                  www.prorack.com.au
NZ: 0800 4776 722                  www.prorack.co.nz

Maintenance

• 

Check accessory is securely attached whenever you re

fi

 t it to the vehicle. If the unit feels loose, refer to the 

fi

 tting 

instructions and readjust.

• 

Regularly check all fasteners. This includes all attached accessories and roof racks.

• 

Remove Straps when not in use.

• 

Clean with hot soapy water and sponge as required.

Содержание VOYAGER PR3207















Отзывы: