Propur ProMax PMC-4000 Скачать руководство пользователя страница 5

 

Step 7 - How to Replace the Filter Cartridge 
 
 
 
 
 
 

1.  Turn off the line piercing needle/saddle valve. Turn on the faucet to release any 

pressure. 

2.  Slowly unscrew the filter housing (1.1), which will be full of water, from the filter 

head (1.2). 

3.  Drain water from the filter housing/sump over sink and remove filter cartridge by  

gently pulling it out from the housing.  
Make sure inside of sump is clean. OK to wash with warm soapy water and rinse 
well. 

4.  Insert new filter cartridge into housing. Make sure cartridge end with washer is  

installed facing upward in housing. Screw housing back onto filter head  
securely. Hand tighten, firmly being careful not to cross thread. 

5.  Proceed to 

Step 6 - Start Up 

and follow instructions. 

 

ProMax

TM  

Under Counter System Specifications 

 

 

Type of installation: Under counter 

 

Maximum Working Pressure: 860 Kpa (125 psig) 

 

NOTE: Should your water pressure exceed 80 psig, install a pressure 

 

reducing valve before installing the system 

 

Minimum Working Pressure: 137 Kpa (20 psig) 

 

Maximum Working Temperature: 38° C (100° F) 

 

Minimum Working Temperature: 5° C (41° F) 

 

Recommended Flow Rate: 0.2 – 1.0 gpm 

 

Contaminant Reduction: Refer to Lab Report 

 

Filter Life Expectancy: Up to 1 year 

 

Replacement filter: PCT3RF 

 

 

CAUTION: 

Never remove the filter housing/sump with  

water pressure in the filter. 

Step 6 - Start-up 

1.  Make sure needles/saddle valve is ready for use.  
2.  Open the faucet fully by lifting the black lever to its vertical position to allow 

trapped air and water to flow out of the system. Make sure spout is  
positioned over the sink. 

3.  Slowly turn on your cold water supply valve under your sink or your house 

supply at the meter. 

4.  Water should start flowing out of faucet. Look at the installation to make 

sure there is no water leaking for any of the fittings, tubing or housing. 

5.  Allow water to flow for about three minutes to flush out the system before 

using the water. Some residual particles may be expelled during the flush; 
this is  
normal. 

6.  Return black lever to off position. 

7.  Your system is now ready for use. 

Содержание ProMax PMC-4000







Отзывы: