NOTE: The use of the Trim buttons are accompanied with a Beep tone. A single long Beep indicates the
product is center trimmed. No beeps after press indicates the product is trimmed to the maximum on a
particular side.
UNDERSTANDING TRIM ADJUSTMENTS
UNDERSTANDING THE ALTITUDE LOCK SENSOR
Forward/Backward Trim
• If your NEUTRON™ is moving forwards or backwards automatically, you may need to adjust the
FORWARD/BACKWARD TRIM buttons.
• If your NEUTRON™ flies forward, push and release the BACKWARD TRIM (B)button repeatedly until
the moving stops and proper flight is maintained.
• If your NEUTRON™ flies backwards, push and release the FORWARD TRIM (F)button in the same
manner until the problem is resolved.
• From time to time you may have to adjust the FORWARD or BACKWARD TRIM buttons to ensure the
NEUTRON™ will hover in mid-air and respond accurately to your commands.
Banking Left/Right Trim
�• If your NEUTRON™ is not steadily hovering and is banking to the left or right automatically, you
may need to adjust the LEFT BANK or RIGHT BANK Trim buttons.
• If your NEUTRON™ banks to the left, push and release the RIGHT BANK TRIM (R)button repeatedly until
the banking stops and proper flight is maintained.
• If your NEUTRON™ banks to the right, push and release the LEFT BANK TRIM (L) button in the same
manner until the problem is resolved.
• From time to time you may have to adjust the LEFT and RIGHT BANK TRIM to ensure the NEUTRON™
will steadily hover in mid-air and respond accurately to your commands.
AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The NEUTRON™ .
• Simply press the “start/land” button on the top of controller, your NEUTRON™ will automatically
take off.
• To stop or land the NEUTRON™ just press the “START/LAND” button again and the NEUTRON™ will
descend and land automatically.
Tips: You also can move the two control sticks simultaneously down to the inside corners, hold them till you
hear a “beep” and the blades start spinning. Release the control sticks and push the throttle stick slowly to
take off manually.
In case of emergency: to stop the rotors instantly, simply press the calibrate button on the top of
the controller, located in the center.
SPEED SETTING BUTTON
The NEUTRON™ has 4 speed settings;
T(Training),1(SLOW),2(MEDIUM)
and
3(HIGH)
. The Default
setting when you first turn on your NEUTRON ™ is
1(SLOW)
. To increase the speed simply press the
speed button(see remote diagram on page 3). You will hear a beep and the speed indicator will display
the current speed setting with the Number. Number
1
indicates slow speed,
2
indicates medium speed
and
3
indicates high speed.
3/4 CHANNEL SELECT
NEUTRON™ allows you to control your Quadrocopter in 3 channel mode (beginner) or 4 channel mode
(advanced flying). The NEUTRON™ default setting is 4 channel mode.
To change to 3 Channel mode:
PRESS the 3CH button (see remote diagram on pg 3), you will hear 3 short beeps indicating the NEUTRON™
now is set to 3CH mode.
To change back to 4 Channel mode:
PRESS the 4CH button (see remote diagram on pg 3), you will hear 4 short beeps indicating the
NEUTRON™ is now set to 4CH mode.
Forward/Backward
Trim Controls
Push and release
to go backward
If flying forward...
5
6
B
Front
F
If flying backward...
Push and release
to go forward
F
4CH
3CH
Forward/Backward
Trim
RECOGNIZING THE FRONT AND REAR OF THE QUADROCOPTER
Left/Right Banking Controls
Push the left button to
increase left banking
sensitivity
Push to right button to
increase right banking
sensitivity
L
R
Bank
Bank
4CH
3CH
The NEUTRON™ has a unique Altitude Lock, air pressure sensor that allows for easier flight control
and stability.
A beginners friend, it allows the user to ease into piloting the copter. The sensor locks in the altitude
of the copter while allowing the user to adjust the directional controls without having to hold the
throttle.
After starting the copter, fly upwards to a safe height using the left joystick. Once at a safe height,
letting go of the left joystick should lock in the altitude and allow the user to focus on getting used
to the directional controls of the NEUTRON™ If when flying , the copter does drift downward or
upward, it will automatically self correct and go back to the last locked height.
NOTE: The altitude sensor does have some tolerance based on atmospheric conditions and could
have a slight variation in altitude.
Even though the Quadrocopter has four rotors there is still a
front or "forward" facing direction and "rear" or backwards
facing direction. The Front and forward facing direction of
the Quadrocopter is the side with two gray blades (see
diagram F ). The rear or backward facing direction of the
Quadrocopter is the side with charging socket and the two
black propellers (see diagram F).
NOTE: The front of the Quadrocopter displays WHITE LED lights
and the back of the Quadrocopter displays RED LED lights.
