4CH
3CH
NOTE: The use of the Trim buttons are accompanied with a beep tone. A single long beep indicates the product is
centre-trimmed. No beeping after press the trim button indicates the product is trimmed to the maximum on a particular side.
UNDERSTANDING TRIM ADJUSTMENTS
Forward/Backward Trim
�• If your ZIPP NANO™2.0 is drifting forwards or backwards automatically, you may need to adjust the
FORWARD/BACKWARD TRIM buttons.
•�If your ZIPP NANO™2.0 drifts forward, push and release the B TRIM button repeatedly until the
drifting stops and proper flight is maintained.
•�If your ZIPP NANO™2.0 flies backwards, push and release the F TRIM button in the same manner
until the problem is resolved.
• From time to time you may have to adjust the FORWARD/BACKWARD TRIM to ensure the
ZIPP NANO™2.0 will hover in mid-air and respond accurately to your commands.
Banking Left/Right Trim
�• If your ZIPP NANO™2.0 is not steadily hovering and is banking to the left or right automatically, you may
need to adjust the BANKING TRIM buttons.
•��If your ZIPP NANO™2.0 banks to the left, push and release the R TRIM button repeatedly until the
banking stops and proper flight is maintained.
•��If your ZIPP NANO™2.0 banks to the right, push and release the L TRIM button in the same manner until
the problem is resolved.
• From time to time you may have to adjust the BANKING TRIM to ensure the ZIPP NANO™2.0 will steadily
hover in mid-air and respond accurately to your commands.
RECOGNIZING THE FRONT AND BACK OF THE ZIPP NANO™2.0
Even though the ZIPP NANO™2.0 has four rotors there is still a
front or forward-facing direction and rear or backwards-facing
direction. TheFront and forward-facing direction of the ZIPP
NANO™2.0 is the side with two holes. The rear of the ZIPP
NANO™2.0 is where the battery charging socket and the
power ON/OFF is. The ZIPP NANO™2.0 when in flight will also
help you observe the orientation with the use of LED lights in
the arms of the ZIPP NANO™2.0.
NOTE: The front of the copter displays WHITE LED lights and the
back of the copter displays RED LED lights.
Forward/Backward
Trim
Forward/Backward
Trim Controls
Push backward
trim button
Push forward
trim button
If flying forward...
If flying backward...
4 CH Left/Right Banking
Controls
Push the “L” trim button to
increase left banking
sensitivity
Push “R” trim button to
increase right banking
sensitivity
Banks Trim
Banks Trim
4CH
3CH
AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The ZIPP NANO™2.0.
• simply press the “start/land” button on the top of controller, your ZIPP NANO™2.0 will automatically
take off.
• To stop or land the ZIPP NANO™2.0 just press the “START/LAND” button again and the ZIPP NANO™2.0
will descend and land automatically.
Tips: You can also move the two control sticks simultaneously down to the inside corners, hold them till you
hear a “beep” and the blades start spinning. Release the control sticks and push the throttle stick slowly to
take off manually.
In case of emergency : to stop the rotors instantly, simply press the calibrate button on the top of
the cotroller, located in the center.
SPEED SETTING BUTTON
The ZIPP NANO™2.0 has 4 speed Modes;
T(Training),1(SLOW),2(MEDIUM)
and
3(HIGH)
. The Default
setting when you first turn on your ZIPP NANO™2.0 is
1(SLOW)
. To exit T Mode and to increase the
speed simply press the speed button(see remote diagram on page 3). You will hear a beep and the
speed indicator will display the current speed setting with the Number. Number
1
indicates slow speed,
2
indicates medium speed and
3
indicates high speed.
T (Training)MODE
Simply press and hold the Speed Modes Button; you will hear a long beep and the speed indicator will
change to "T." Now you are in T mode. T mode allows you to learn how to operate your ZIPP NANO™2.0
at a very slow speed. To exit T mode just press the speed setting button again.
AUTO-SHUT-OFF
In T-Mode and Mode 1 (with safety cage fitted), The ZIPP NANO™2.0’s motors will automatically shut
off when it comes into contact with the ground, walls or any other objects. This is a safety feature for
beginner pilots and is disabled in modes 2 and 3.
3/4 CHANNEL SELECTION
ZIPP NANO™2.0 allows you to control your Quadrocopter in 3 channel mode (beginner) or 4 channel
mode (advanced flying). The ZIPP NANO™2.0 default setting is 4 Channel mode.
To change to 3 Channel mode:
PRESS the 3CH button (see remote diagram on pg 3); you will hear 3 short beeps indicating the ZIPP
NANO™2.0 now is set to 3CH mode.
To change back to 4 Channel mode:
PRESS the 4CH button (see remote diagram on pg 3); you will hear 4 short beeps indicating the Zipp
Nano™ is now set to 4CH mode.
Rear
5
6
Front
A
B
B
A
If you have successfully synced your ZIPP NANO™2.0 to your controller as explained on page 4 you are now
ready to fly. Before beginning to fly your drone you should familiarize yourself with how to start and stop
the rotors, how to use your take off and auto land feature and how the controls work. please carefully read
and familiarize yourself with various control features explained in the next few pages. Once again as a
beginner pilot you should learn how to control your drone in a large open field or park on a day with zero or
very light wind. Do not try to fly your ZIPP NANO™2.0 too high until you become a more experienced pilot.
NOW YOU ARE READY TO FLY!
