ZIPP NANO™ 2.0 DIAGRAM
REMOTE DIAGRAM
Landing Gear
Safety Guard
Rotor Blade
FLYING TIPS
• It is recommended that you operate the ZIPP NANO™2.0 in a wide open space. The ideal space should
have a 61 m/200 ft radius.
• Parental guidance or adult supervision is suggested at all times.
• If you are flying the ZIPP NANO™2.0 with others, make sure all spectators are behind you.
• For best performance, it is recommended that you operate the ZIPP NANO™2.0 in zero wind conditions.
Wind can greatly affect the performance of the ZIPP NANO™2.0.
Important! When syncing your ZIPP NANO™2.0 copter with the controller always make sure that
the quadcopter is on a flat level surface. This insures that the 6-axis gyro is properly programmed
to mimic your trim settings.
Your
ZIPP NANO™2.0
utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly
side by side in the same wireless range.
For One-person Play:
1. Before starting, make sure that the power on both your controller and ZIPP NANO™2.0 are in the OFF
position. Make sure that there are no other 2.4G devices in the area as well.
2. Turn ON the ZIPP NANO™2.0 and set it down on a flat level surface. The white and red LED indicators of
the ZIPP NANO™2.0 should flash.
3. Turn ON your remote and you will hear 2 short beeps,the white and red LED lights will start flashing
slower. Push the throttle all the way up and pull it down; You will hear 2 beeps and the LED
lights will turn solid, your ZIPP NANO™2.0 and remote should have successfully synced. Should this
not happen, repeat all steps again.
For Multi-person Play:
4. Before starting, make sure that the power on all ZIPP NANO™2.0s and Controllers are in the OFF
position. Make sure that there are no other 2.4G devices in the area as well.
5. Each person will have to sync their ZIPP NANO™2.0 individually at a different time to avoid
interference. Follow steps 1 to 3 above, making sure to keep away from other people while also
making sure that no one else is syncing at the same time.
6. After syncing a player's ZIPP NANO™2.0, it should be left ON until all players have synced their ZIPP NANO™2.0s.
7. Should there be a mistake/interference, all players must turn off their controllers and
ZIPP NANO™2.0s and start the process all over again.
SYNCING YOUR ZIPP NANO™2.0
Power On/Off
Charging
Socket
DO NOT FLY YOUR ZIPP NANO™2.0 IN FOUL WEATHER!
WARNING
• Verify that there are 2 “AAA” batteries inside the remote control unit and the ZIPP NANO™2.0 has been fully charged.
• Make sure to be in a large open space with an radius of at least 50 feet.
• Make sure the empty space has no obstacles or rivers.. Set your ZIPP NANO™2.0 on a flat level surface before take-off.
DO NOT ATTEMPT TO FLY YOUR ZIPP NANO™2.0 IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR
LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.
PREPARING FOR FLIGHT
REMOVABLE CONTROLLER GRIPS
Easily slide off and on. (see grip extenders card)
The safety guard is easy to clip on and off. Simply pull the clips away
from each motor mount and remove the ZIPP NANO™2.0 from below.
Note: Always have the safety guard attached when flying in T-Mode and Mode 1.
3
4
OFF ON
Speed Setting Button
AUTO Start / land
Calibrate Button
Speed Indicator
Throttle/Yaw
360˚ Stunt Rolls Button
Direction Control
Power On/Off
4CH
3CH
4 CH Mode
Removable grip
Extender
3 CH Mode
Left Bank Trim
Right Bank Trim
Forward Trim
Power Indicator
Backward Trim
1 2
CALIBRATE
STUNT
START/LAND
SPEED
T
H
3 4 C
3
