Pronto M61 Скачать руководство пользователя страница 28

Страница: 28 / 80

SECTION 5—WHEELCHAIR OPERATION

Pronto® M61™with SureStep®

Part No. 1139640

SECTION 5—WHEELCHAIR

OPERATION

WARNING

After any adjustments, repair or service and before use, make sure that all attaching

hardware is tightened securely - otherwise injury or damage may result.
The electronics control unit is programmed with standard values during manufac-

ture. Set-up of the Electronics Control Unit is to be performed only by a qualified

technician. The final adjustments of the controller may affect other activities of the

wheelchair. Damage to the equipment could occur if improperly set-up or adjusted.

Turning the Power On/Off

NOTE: For this procedure, refer to FIGURE 5.1.

1. To turn the power On by pressing the

On/Off button.

NOTE: After turning power on, the battery

gauge indicators will light briefly. One of the

following will occur after that:

•

The current battery charge will be indicated

on the information gauge display.

• Lock Mode will be indicated by all LEDs

flashing briefly and the information gauge

LEDs chasing slowly from right to left. If

this occurs, press the horn button two times

within ten (10) seconds to unlock the

joystick.

FIGURE 5.1

Turning the Power On/Off

2. Turning the power Off can be achieved by pressing the On/Off button.

NOTE: If the joystick has been programmed for lock mode, holding the On/Off button down for

four seconds will lock the joystick. The LEDs will flash briefly and the horn will sound a short beep.

On/Off

Button

Information

Gauge Display

Содержание M61

















































































Результаты поиска

Содержание M61

Отзывы:

Похожие инструкции для M61

Бренды по названию

Популярные бренды

Pronto M61, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание M61

Отзывы:

Похожие инструкции для M61

Бренды по названию

Популярные бренды