PRONAR ZEFIR 85 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 88

PRONAR ZEFIR 85 Скачать руководство пользователя страница 63

PRONAR

F. TECHNICAL MAINTENANCE OF THE

TRACTOR

PRONAR

53

TECHNICAL REVIEWS TABLE

Technical review after each

(mth):

PC

P-2

P-3

P-4

No. of

action

Servicing activities

(10*)

(200)

(400)

(800)

Technical review (TR) after each 10 mth (or every day)

1

Check oil level in the engine

X

X

X

X

1a

Inspect the degree of contamination and oil level in oil sump
of the air filter (engine version with wet air filter) or degree of
contamination of dry filtration elements of the air filter
(engine version with dry oil filter)

X

X

X

X

2

Inspect oil level in the tank of the steering system

X

X

X

X

3

Check cooling agent level in the cooler

X

X

X

X

4

Check hydraulic oil level in the tank of hydraulic system for
steering with brakes

X

X

X

X

5

Inspect liquid level in the tank of front windscreen washer

X

X

X

X

6

Check fuel level in fule tank

X

X

X

X

7

Check and remove deposits (impurities) from the preliminary
sedimentation tank of the fuel filter and fuel tank

X

X

X

X

8

Check technical condition of tyres and tyre pressure.

X

X

X

X

9

Remove condensation water from the tank of the pneumatic
system

X

X

X

X

10

Inspect tightness of all external screw joints, especially of
wheel hubs of both front and rear tractor wheels.

X

X

X

X

11

Lubricate the water pump shaft and wheel hubs of rear
wheels of the tractor

X

X

X

X

12

Remove all leakages and lack of tightness in fuel system,
hydraulic system, cooling system and engine air inlet
system.

X

X

X

X

13

Inspect the engine, steering system, braking system and all
other system and assemblies of the tractor

X

X

X

X

14

Replace filtering cut-off wall in hydraulic oil filter

Replace every 8 mth for first 64

mth of operation.

15

Check the tension of driving belt of the fan

Every 50mth

16

Lubricate front axle revolution pin, joints of the servomotor of
steering system, elements of rear three-point hang-up
system, joint of driving shaft of the front axle

Every 50mth

Technical review (P-2) after each 200 mth

17

Change oil and oil filter in the engine

X

X

X

18

Replace filtering element of the rough and fine fuel filter and
deaerate fule system

X

X

X

19

Replace filtering element together with oil filter cut-off wall of
the hydraulic system

X

X

X

20

Change oil in oil sump of the air filter and clean its filtering
elements (engine version with wet air filter)

X

X

X

21

Clean air filter in the compressor

X

X

X

22

Check tightness of the engine head

X

X

X

23

Inspect and adjust valve clearance

X

X

X

Technical review (P-3) after each 400 mth

24

Check oil level in hydraulic system, gear-box and rear axle

X

X

25

Check oil level in main gear and wheel reduction gears of
the front driving axle

X

X

26

Verify parking brake performance (dead movement of the
lever)

X

X

27

Lubricate bearings of stub-axle of wheel reduction gears of
the front axle

X

X

«
...
61
62
63
64
65
...
»

Содержание ZEFIR 85

























































































Отзывы:

Нет отзывов