Promotech PRO 5 PB Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 31

background image

PRO 5 PB/PBE/PBC

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

8

21. Do not touch moving parts or metal chips formed during milling. Prevent objects

from being caught in moving parts.

22. After every use, remove metal chips and excess coolant from the machine. Never

remove chips with bare hands. Clean

the

machine

with a cotton cloth without

using any agents.

23. Cover steel parts with a thin anti-corrosion coating to protect the machine from

rust when not in use for any extended period.

24. Maintain

the

machine

and

install/remove

parts

and

tool

bits

only

when the machine

is unplugged from the air (power) source.

25. Repair only in a service center appointed by the seller.

26. If the machine falls from any height, is wet, or has any other damage that could

affect the technical state of the machine, stop the operation and immediately

send the machine to the service center for inspection and repair.

27. Never leave the machine unattended during operation.

28. Remove

from

the

worksite

and

store

in a secure and dry location when not in use,

previously removing the tool bits from sockets.

«
...
6
7
8
9
10
...
»

Содержание PRO 5 PB
































Отзывы:

Нет отзывов

Похожие инструкции для PRO 5 PB

Бренд: 3M Страницы: 2

Бренд: Jacobs Ladder Страницы: 16

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

AquaPure Ei Series

Бренд: Jandy Страницы: 4

Бренд: janitza Страницы: 30

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: Gaspardo Страницы: 44

Бренд: VaBroom Страницы: 4

Ti-Max NLX nano

Бренд: NSK Страницы: 38

Бренд: Sensio Страницы: 3

Бренд: ZAMST Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды