promesstec UMU-FD 2 Скачать руководство пользователя страница 7

 

promesstec  GmbH

  I  Niedersachsenstraße 4  I  D- 48465 Schüttorf  I  Tel.:+49 (0)5923/ 90 229 0  I  Fax:+49 (0)5923/ 90 229 29 

E-Mail: [email protected]  I  Internet: www.promesstec.com   

3.2  Stuff qualification 

 

Improper handling  can  result  in  considerable  injury  and  damage  to 
equipment.  The  activities  described  in  these  operating  instructions 
may only be carried out by skilled stuff who have the qualifications 
described below. Keep unqualified stuff away from hazardous areas. 
 

For  installation and  starting  of the flow-meter  the  stuff  has  to  be familiar  with  the 
relevant  regulations and directives of the country and must  have the qualification 
required. They must have knowledge on measurement and control technology, have 
to be acquainted with electric circuits, are capable of carrying out the work described 
and  can  independently  recognize  potential  hazards.  Depending  on  the  operation 
conditions of the application they have to have the corresponding knowledge, e.g. 
of aggressive media.. 
 

3.3  Special hazards  

 

Comply with the country-specific regulations (e.g. standards) and 
observe the applicable standards and guidelines for special applica-
tions (e.g. for hazardous media such as acetylene, combustible or 
toxic substances as well as for refrigeration systems and compres-
sors). 
Failure to comply with the relevant regulations can result in serious 
personal injury and damage to property

 

A protection from electrostatic discharge (ESD) is required. The pro-
per use of grounded work surfaces and personal wrist straps is re-
quired  when  working  with  exposed  circuitry  (PCB,  printed  circuit 
boards), in order to prevent static discharge from damaging sensitive 
electronic components. 

There is a danger of death caused by electric current. Upon contact 
with life parts, there is a direct danger of death. Electrical instruments 
may only be installed and connected by skilled electrical personnel. 
Operation using a defective power supply unit (e.g. short circuit from 
the mains voltage to the voltage output) can result in life-threatening 
voltages at the instrument. 

Residual media in dismounted instruments can result in a risk to per-
sonnel, the environment and equipment. Take sufficient precaution-
ary  measures.  Do  not  use  this  instrument  in  safety  or  Emergency 
Stop  devices.  Incorrect  use  of  the  instrument  can  result  in  injury. 
Should  a failure  occur,  aggressive  media  with  extremely  high  tem-
perature and under high pressure or vacuum may be present at the 
instrument. 

Содержание UMU-FD 2
















Отзывы: