Promac JMDT-804516-DRO, Руководство пользователя

Страница: 4 / 17

4
Before operating the machine, remove
tie, rings, watches, other jewellery, and
roll up sleeves above the elbows.
Wear safety shoes; never wear leisure
shoes or sandals.
Always wear the approved working
outfit.
Do
not wear gloves.
Wear goggles when working
Install the machine so that there is
sufficient space for safe operation and
work piece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be bolted to the
cabinet stand or a solid work bench.
Make sure that the power cord does not
impede work and cause people to trip.
Keep the floor around the machine
clean and free of scrap material, oil and
grease.
Stay alert!
Give your work undivided attention. Use
common sense. Do not operate the
machine when you are tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it is
operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Keep children and visitors a safe
distance from the work area.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Work only with well sharpened tools.
Always close the chuck guard and
pulley cover before you start the
machine.
Remove the chuck key and wrenches
before machine operation.
Specifications regarding the maximum
or minimum size of the work piece must
be observed.
Do not remove chips and work piece
parts until the machine is at a standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried out
by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Never place your fingers in a position
where they could contact any rotating
tool, chuck or cutting chips.
Secure workpiece against rotation. Use
fixtures, clamps or a vice to hold the
workpiece.
Never hold the workpiece with your
hands alone.
When using a vice, always fasten it to
the table.
Never do any works “freehand” (hand-
holding the work piece rather than
supporting it).
Never move the head while the machine
is running.
If a work piece overhangs the table such
that it will fall or tip if not held, clamp it to
the table or provide auxiliary support.
Check the save clamping of the work
piece before starting the machine.
Remove cutting chips with the aid of an
appropriate chip hook when the
machine is at a standstill only.
Never stop the rotating chuck or tool
with your hands.
Measurements and adjustments may be
carried out when the machine is at a
standstill only.
Setup work may only be carried out
after the machine is protected against
accidental starting by pressing the
emergency stop button.
Maintenance and repair work may only
be carried out after the machine is
protected against accidental starting by
pulling the mains plug.
Do not use wire wheels or grinding
wheels on this machine.
To avoid injury from parts thrown by the
spring, follow instructions exactly as
given when adjusting the spring tension
of the quill (see chapter 7.5)
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist.
The rotating chuck, tool and cutting
chips can cause injury.
Thrown and hot work pieces and cutting
chips can lead to injury.
Chips, dust and noise can be health
hazards. Be sure to wear personal
protection gear such as safety goggles,
dust mask and ear protection.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
4. Machine specifications
4.1 Technical data
JMDT-804516-DRO:
Drilling capacity(Iron/Steel) 45/45*mm
Milling capacity of face mill 80mm
Milling capacity of end mill 32mm
Tapping capacity(Iron/Steel) 16/16*mm
(*not for intense operations)
Spindle to column
260mm
Distance table to spindle max 460mm
Spindle taper MT-4
Draw bar M16
Spindle travel 120mm
Spindle speeds… 75-435/435-2500rpm
Max travel X-axis 560mm
Max travel Y-axis 190mm
Table size 240x800mm
T-slots...3 14mm
Overall (LxWxH) 1050x980x2100mm
Net weight 480 kg
Mains 3~400V, PE, 50Hz
Output power 1,5 kW S1
Reference current 3.7A
Extension cord (H05VV-F): 4Gx1,5²
Installation protection 6-10A
4.2 Noise emission
Acoustic pressure level (EN 11202):
Idling at maximum speed 85 dB (A)
The specified values are emission levels
and are not necessarily to be seen as
safe operating levels.
As workplace conditions vary, this
information is intended to allow the user
to make a better estimation of the
hazards and risks involved only.
4.3 Content of delivery
1-13mm drill chuck with arbour MT4
Draw bar M16
Head rising crank and handle
3 Table handwheels
Operating tools
Operating manual
Spare parts list.
5. Transport and start up