background image

PROLIGHTS - EclExpo

 Flood300VW

23

14 - MAINTENANCE

MAINTENANCE AND CLEANING THE PRODUCT

WARNING: Disconnect from the mains before starting any maintenance work

It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or 

other particles to ensure that the light is radiated at maximum brightness.

• 

For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a 

mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, 

clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.

•  The user must clean the product periodically to maintain optimum performance and cooling. The 

user may also upload firmware (product software) to the fixture via the DMX signal input port or USB 

port using firmware and instructions from PROLIGHTS.

•  The frequency of such maintenance operations is to be performed according to various factors, such 

as the amount of the use and the condition of the installation environment (air humidity, presence 

of dust, salinity, etc.). It is recommended that the product is subject to annual service by a qualified 

technician for special maintenance involving at least the following procedures:

•  General cleaning of internal parts.

• 

Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by PRO-

LIGHTS.

•  General visual check of the internal components, cabling, mechanical parts, etc.

•  Electrical, photometric and functional checks; eventual repairs.

•  Cleaning the lenses. Only use neutral soap and water to clean the lenses, then dry it carefully with 

a soft, non-abrasive cloth.

WARNING: the use of alcohol or any other detergent could damage the lenses.

•  All other service operations on the product must be carried out by PROLIGHTS, its approved service 

agents or trained and qualified personnel.

•  It is PROLIGHTS policy to apply the strictest possible calibration procedures and use the best quality 

materials available to ensure optimum performance and the longest possible component lifetimes. 

However, optical components are subject to wear and tear over the life of the product, resulting 

in gradual changes in colours over many thousands of hours of use. The extent of wear and tear 

depends heavily on operating conditions and environment, so it is impossible to specify precisely 

whether and to what extent performance will be affected. However, you may eventually need to re

-

place optical components if their characteristics are affected by wear and tear after an extended pe

-

riod of use and if you require fixtures to perform within very precise optical and colour parameters.

• 

Do not apply filters, lenses or other materials on lenses or other optical components. Use only ac-

cessories approved by PROLIGHTS.

REPLACING THE FUSE

WARNING: Before replacing the fuse, unplug the product from the mains.

•  Remove the old fuse from the housing with a suitable screwdriver (anticlockwise) and replace it with 

one of the same type and of the same classification (T6.3 AL 250V).

VISUAL CHECK OF PRODUCT HOUSING

•  The parts of the product cover/housing should be checked for eventual damages and breaking 

start at least every two months. In addition, especially the parts of the front lens holder have to be 

checked mechanically (by means of movement by the part) if it is firmly fastened to the fixture. If 

hint of a crack is found on some plastic part, do not use the product until the damaged part will be 

replaced.

•  Cracks or another damages of the cover/housing parts can be caused by the product transportation 

or manipulation and also ageing process may influence materials.

• 

This checking is necessary for both fixed installations and preparing product for renting. Any free 

moving parts inside of the product, cracked cover/housing or any part of front lens not sitting prop

-

erly in place need to be immediately replaced.

Содержание EclExpo Flood300VW





























Отзывы: